Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Chinese laser purchase/Shenui/Laserworks tips and tricks thread
Thread Starter: Rodne Gold
Considering a lot of us are going or have gone that direction , I thought it a good idea to combine our knowledge pool in one thread. So I have started one. Those of you that have already posted to other threads can perhaps repeat and consolidate the posts here or at least point to other posts on...
Last Post By: George Carlson Today, 9:07 AM

Your Best Nifty Shop Tip?
Thread Starter: Russell Neyman
It's the small things that often make the biggest difference. I've found that the crafty veterans seem to know a little trick here or there that make turning better, safer, faster, or easier. So I'm throwing out a challenge: give us your best "nifty" and when this thread is done, it will make a...
Last Post By: Rich Stewart Today, 11:48 AM

Sharpening technique--removing the wire edge
Thread Starter: Steve Voigt
Hi all, This post may portray me as embarrassingly stupid and inefficient, but whatever. Here goes. For the last 15 years, regardless of the sharpening media, I have used the following method: 1) hone a secondary bevel on a coarse stone until I can feel the wire edge on the back, all the way...
Last Post By: george wilson Today, 3:19 PM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: John Champlain Today, 11:58 AM

How about a little side contest? Make a Pencil sharpener...
Thread Starter: David Weaver
The catch being, make it completely and totally by hand. No electric at all with the possible exception of drilling a hole in the cutter. In the world of everything being sharp working better, I'm thinking that those little hand twist manual sharpeners would work pretty well if the cutter in them...
Last Post By: Jon Shank Yesterday, 11:43 PM

Lie Nielsen new waterstones
Thread Starter: Dave Cav
If didn't have a good set of Shapton pro stones I'd be looking at these. The combo stones appear to be a pretty good deal. http://www.lie-nielsen.com/catalog.php?sku=2-OHISHII
Last Post By: David Weaver Today, 12:18 PM

Larry Browning

There is no available content written by Larry Browning

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

Leaf ID #4

Mulberry is supposed to be "very, hard, heavy and durable".
Bill Rogers Today, 5:52 PM

Leaf ID #3

I agree with Tim: Box Elder. It is a fairly soft maple that is "light, soft and close-grained; easy to work".
Bill Rogers Today, 5:49 PM

Any tips on removing a riciculously glued rubber tire from lower BS wheel?

Naphtha is inexpensive (and the active ingredient in other adhesive removers although doesn't leave a residue like goo-gone and others) and has dissolved
glenn bradley Today, 5:41 PM

Blum hinge question

Ouch. I do see the problem but, with assembly complete, I'd be tempted to notch the stop for clearance. If an alternate hinge is a guaranteed fix, I
glenn bradley Today, 5:36 PM

Shop-Made Toolbox Thread

Von,

Of course! Notice the photo of me by the rig - that was to show scale. Eyeballs just can see what is in the top . Guess you could call
Tom Clark FL Today, 5:32 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Larry Browning

Recent Polls

Recent Forum Posts

Recent Blog Posts