Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Rabbit owners
Thread Starter: James Jaragosky
Please introduce yourself. If you could also put what model machine you have, and how long you have had it That would really help. My purpose in creating this thread is so we can help support each other, Because as you all know by now, factory support for everyday problems is limited. And there...
Last Post By: Ernie Balch Today, 11:32 AM

Sharpening technique--removing the wire edge
Thread Starter: Steve Voigt
Hi all, This post may portray me as embarrassingly stupid and inefficient, but whatever. Here goes. For the last 15 years, regardless of the sharpening media, I have used the following method: 1) hone a secondary bevel on a coarse stone until I can feel the wire edge on the back, all the way...
Last Post By: george wilson Yesterday, 3:19 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: James White Today, 10:22 AM

Any updates on the Veritas shooting board plane?
Thread Starter: Scott Stafford
I thought it best to check to see if anyone has heard of any progress on the Veritas shooting board plane. Timeline? Features? I'm ready to buy a Lie-Nielsen 51 but thought it best to see what anyone had read or heard lately of the unofficially announced Veritas. I might be able to...
Last Post By: Peter Pedisich Today, 9:57 AM

A Scientist Explains The Physics of Resawing
Thread Starter: Julie Moriarty
I don't know he's a scientist...:rolleyes:
Last Post By: Metod Alif Today, 8:34 AM

How Do You Make This Cut?
Thread Starter: Julie Moriarty
Cut offs were clamped in place to show the "before" state. I've been confronted with this type of thing many times, tight conditions, you can't take it into the shop, no small plunge cut saw, etc. And you don't want a huge mess because you're working in a lived-in area. In this case, the...
Last Post By: Andy Pratt Today, 10:46 AM

Jim Eller

There is no available content written by Jim Eller

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

Cleaning HVLP

I have a Fuji with gravity cup so cleaning shellac takes as little as spraying roughly 10-15 cl of DNA and then a rag with DNA to wipe the cup inside
Darius Ferlas Today, 12:27 PM

Is a Sargent plane worth having?

Just went back and bought it! Cant wait to clean it up. Peter, Im going to try and make it look like yours. Also, oddly enough I made a mallet exactly
Frederick Skelly Today, 12:21 PM

Help, Doors won't close

Based solely on the pictures I see little indication of faulty hinge installation.
Are you sure the door is flat?
Darius Ferlas Today, 12:20 PM

Help, Doors won't close

Hello,
I am building a nightstand with two doors on the front bottom. I have used SOSS hidden hinges for the doors. One of the door closes almost
earl wojciechowski Today, 12:09 PM

Are 2" wide face frames too wide?

I always use 2" face frames, unless it is going to be a small cabinet. The overlay doors will reduce the visual size anyway. My raised panel doors
Rick Potter Today, 12:06 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Jim Eller

Recent Polls

Recent Forum Posts

Recent Blog Posts