Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Chinese laser purchase/Shenui/Laserworks tips and tricks thread
Thread Starter: Rodne Gold
Considering a lot of us are going or have gone that direction , I thought it a good idea to combine our knowledge pool in one thread. So I have started one. Those of you that have already posted to other threads can perhaps repeat and consolidate the posts here or at least point to other posts on...
Last Post By: George Carlson Yesterday, 7:32 PM

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: Steve Fulgoni Yesterday, 10:44 PM

Vote For Your Favorite Baileigh Box Contest Entry
Thread Starter: Bill Wyko
Ok, we need some pictures. While many of you will be using lasers my friend Paul has a Chevalet. This tool was created in the late 1700's for production marquetry. It has a foot activated clamp to hold your stack of veneers and a "D" shaped saw that is held perpendicular to your cut but will move...
Last Post By: Bill Wyko Yesterday, 6:18 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: David Kumm Yesterday, 11:11 AM

Pterocarpus Rex drum set
Thread Starter: Seth Dolcourt
Hi, Creekers, Back for another drum project. This one's gonna be big. And, it will take a while. Pterocarpus is the genus for the market name of padauk, and Pterocarpus Rex is a play on T Rex. This is a collaboration with a guy who will finish, drill and deliver the drums to his own...
Last Post By: Mark Crenshaw Yesterday, 11:10 AM

Memorial day must be coming....
Thread Starter: Jeff Monson
Unleaded went from $3.79 this morning to $4.09 in a matter of minutes. 30 cents is quite a hike, cant tell me the gas stations aren't smiling for a couple days.
Last Post By: Brian Elfert Yesterday, 11:26 PM

Frank Pellow

There is no available content written by Frank Pellow

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

Need an idea fast

Jeff

I am short on suggestions but I like using leather as a substrate as it engraves beautifully, looks very good and, cared for properly,
Mike Null Today, 7:03 AM

Laser Engraving True 8bit Shades of Grey

Michael,

That came out very nice. To answer your question, no there is no material being removed, but we have experimented with something
Jeff Woodcock Today, 6:58 AM

Boeken Hout bord (Cape Beech Plate)

Dankie Phil

Where is Rosetta?

No the slab I have is as hard as hell, but one can see that it was a big tree. It is grainy and
Glenda Marais Today, 6:45 AM

Lie Nielsen new waterstones

Ha. That's insanity, even for me, even for razors. I think at that level one would just flay of their skin...bit too close of a shave for my taste.
Chris Griggs Today, 6:39 AM

I made the switch...

Mike,

Since you had both the Stronghold and the Hurricane, did you ever get a chance to check the thread adapters?
i.e. can the
Olaf Vogel Today, 6:34 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Frank Pellow

Recent Polls

Recent Forum Posts

Recent Blog Posts