Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Chinese laser purchase/Shenui/Laserworks tips and tricks thread
Thread Starter: Rodne Gold
Considering a lot of us are going or have gone that direction , I thought it a good idea to combine our knowledge pool in one thread. So I have started one. Those of you that have already posted to other threads can perhaps repeat and consolidate the posts here or at least point to other posts on...
Last Post By: Hermes Sandoval Yesterday, 12:57 PM

Your Best Nifty Shop Tip?
Thread Starter: Russell Neyman
It's the small things that often make the biggest difference. I've found that the crafty veterans seem to know a little trick here or there that make turning better, safer, faster, or easier. So I'm throwing out a challenge: give us your best "nifty" and when this thread is done, it will make a...
Last Post By: Russell Neyman Yesterday, 7:18 PM

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: Roy Turbett Yesterday, 8:22 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: David Kumm Yesterday, 11:01 PM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: Jeff Woodcock Yesterday, 6:08 PM

Buy versus build?
Thread Starter: Jamie Buxton
Because we're builders, we can make stuff for our shops. We also have manufacturers which are happy to sell us similar stuff. For instance, you can make your own sawhorses, or you can buy them. You can make a workbench, or you can buy one. You can make your own jigs (for instance a shelf-pin...
Last Post By: Larry Browning Yesterday, 10:25 PM

fred marcuson

There is no available content written by fred marcuson

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

Parks planer refurb

DON'T beat on it, Bill.
There's 2 possibilities. A burr caused by the set screw ... or rust between the shaft and the gear.
You'll need at
Sam Puhalovich Today, 5:09 AM

Any tips on removing a riciculously glued rubber tire from lower BS wheel?

If it's contact cement, use wax & grease remover, you can get it at automotive finish stores. It's used to remove wax, grease, tar, glue, oil etc.
Bill Wyko Today, 4:09 AM

My workbench almost finished

Very well done, I too did square dog holes on my bench. I'm almost done too. ran out of wood though.
Bill Wyko Today, 4:03 AM

Rowmark Supplier UK

Can someone please recommend a reliable online supplier of Rowmark flexi brass in the UK. I have found a couple but you either have to phone and order
Carrol Fleming Today, 4:00 AM

My workbench almost finished

Looking good Tai. Sturdy too, and you sure can't beat the price.

Rick Potter
Rick Potter Today, 3:33 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

fred marcuson

Recent Polls

Recent Forum Posts

Recent Blog Posts