• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Jerome Stanek

    Glowforge release

    Thread Starter: Jerome Stanek

    I was wondering if Glowforge has sent out any units yet. I thought they were supposed to release the middle of December.

    Last Post By: Bert Kemp Yesterday, 8:59 PM Go to last post
    Mike Heidrick

    Pole Barn 40X64X16

    Thread Starter: Mike Heidrick

    Signed a contract yesterday with S&L Builders out of Indiana for a 40X64X16 Pole Barn with a 10X24 porch. Build date August 18, 2014. Plan to install Pex for raidant floor heat. Concrete slab 5" thick. Also doing 1.5" closed cell foam under the pad. Built on Laminated posts in ground. Will...

    Last Post By: Mike Heidrick Yesterday, 12:37 AM Go to last post
    Victor Robinson

    Poll: Curious about Festool ownership

    Thread Starter: Victor Robinson

    Just scratching an itch... Even though Festool and Sawstop now have the same parent company, for the purposes of this poll, please do not count a Sawstop as a Festool.

    Last Post By: Paul Yager Yesterday, 11:27 PM Go to last post
    Steven Harrison

    I Need Help with Lie-Nielsen Planes

    Thread Starter: Steven Harrison

    Two part questionÖ First Iím gearing up to order a Lie-Nielsen jointer, either a 7 or 8. The largest plane I have now is an older Stanley #6. I like the idea of the 8, but in practice Iím worried itís too wide to edge joint 3/4Ē which is what I mainly work with, but sometimes thinner. Iím not...

    Last Post By: Jim Koepke Today, 12:18 AM Go to last post
    Prashun Patel

    Farmhouse table

    Thread Starter: Prashun Patel

    I'm building this for some friends. The customer does not want a typical lower-mounted stretcher as is found on every Pinterest post. I'm taking a cue from the Shakers and putting a wide stretcher up top under the table. My desk uses this type of construction and I've not had issues with...

    Last Post By: Jody Amerson Yesterday, 4:29 PM Go to last post
    David Ragan

    Objectifying edge quality

    Thread Starter: David Ragan

    How do you all gage sharpness? I have a couple of micro cameras, but setting all that up is a hassle. There is the thread method by Steve Elliott or Brent Beach, I forget which. Last wkd, I had some LV plate w 3M film, did some free hand swipes on a plane, and had good results-satisfied. ...

    Last Post By: Patrick Chase Yesterday, 1:18 PM Go to last post
  • Rich Konopka

    There is no available content written by Rich Konopka
  • Recent Polls

    SawStop Ownership (Votes: 2)

    1. I will never buy a SawStop (Votes: 0)

    2. I may or may not buy a SawStop TBD balance of price/features next time I'm looking for a saw (Votes: 0)

    3. I will definitely be buying a SawStop (Votes: 0)

    4. I own a SawStop (Votes: 2)

    5. I regret not buying a SawStop sooner due to a TS accident (Votes: 0)

  • Recent Forum Posts

    Bradley Potts

    Kerf marks?

    Yep, Glenn you are on the money.

    It's probably a good idea to dial this all back to the fundamentals. If we're getting saw marks, that simply

    Bradley Potts Today, 12:33 AM Go to last post
    Mark Taylor2

    1 week stats, engraving forums

    You guys are way out of my league. Here's latest I've done... cannon carriages for a model wooden ship I'm scratchbuilding.

    Mark Taylor2 Today, 12:25 AM Go to last post
    John K Jordan

    First Turning with the new lathe


    When I turn a flat bottom with a flat ended scraper like that I do two things: grind it with a top bevel (the negative rake) and

    John K Jordan Today, 12:24 AM Go to last post
    Jim Koepke

    I Need Help with Lie-Nielsen Planes

    Thanks for the smile Kurtis.

    Having my shop open to others has so far allowed me to meet some very nice people. Funny story about this is

    Jim Koepke Today, 12:18 AM Go to last post
    Mike Heidrick

    Collection of collectors

    A ten, two fives, and a three. I am just a junior collector member.

    Mike Heidrick Today, 12:11 AM Go to last post
  • Recent Blog Posts