• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Jerome Stanek

    Glowforge release

    Thread Starter: Jerome Stanek

    I was wondering if Glowforge has sent out any units yet. I thought they were supposed to release the middle of December.

    Last Post By: Dave Stevens-Vegas Today, 4:43 AM Go to last post
    Mike Heidrick

    Pole Barn 40X64X16

    Thread Starter: Mike Heidrick

    Signed a contract yesterday with S&L Builders out of Indiana for a 40X64X16 Pole Barn with a 10X24 porch. Build date August 18, 2014. Plan to install Pex for raidant floor heat. Concrete slab 5" thick. Also doing 1.5" closed cell foam under the pad. Built on Laminated posts in ground. Will...

    Last Post By: Mike Heidrick Today, 1:21 AM Go to last post
    Stanley Covington

    The Essential Oilpot

    Thread Starter: Stanley Covington

    The oilpot is an essential tool for precision woodworking. I first learned this fact while living in Japan when I was called a fool by a joiner for not having one in my tool kit. I won't bore you with that embarrassing story, but a quick tutorial on oilpots as I understand them may be useful. ...

    Last Post By: Stewie Simpson Yesterday, 11:30 PM Go to last post
    Tim Bridge

    Making a Living Woodworking

    Thread Starter: Tim Bridge

    Is it possible to make a living woodworking out of my garage making small projects and selling them at flea markets or other places? I have a bandsaw, router table, planer, miter saw, table saw, spindle sander, drill press and an assortment of hand tools. I am tired or working for electrical...

    Last Post By: Martin Wasner Yesterday, 6:34 PM Go to last post
    Brian Kent

    Oops

    Thread Starter: Brian Kent

    Just glad I had that steady rest to that if I had a catch it wouldn't pry the bank loose. In this case I barely touched the rim with the tip of a v scraper. On the end of the 10" chalice, the physics works against me. I have a whole lot of long work to do (23 more chalices 10" x 3.5") so I...

    Last Post By: Stan Smith Yesterday, 5:16 PM Go to last post
    Dan Schmidt

    Slider Questions

    Thread Starter: Dan Schmidt

    1 - for those of you who use sliders to rip 4x8 sheets, is such a support on the sliding bed necessary (shown here with red arrow) to support the back left corner of the sheet? 2 - for those of you with Felder units specifically, do you have the new swing-away overhead blade guard as shown...

    Last Post By: Brian Lamb Yesterday, 11:38 AM Go to last post
  • Ted Calver

    There is no available content written by Ted Calver
  • Recent Polls

    Which vice for sawing (Votes: 30)

    1. Face vice (Votes: 13)

    2. Moxxon vice (Votes: 13)

    3. Other (Votes: 4)

  • Recent Forum Posts

    Larry Edgerton

    Is a Starrett a Starrett?

    I don't know Prashun, there is something about using a quality layout tool that I think you would really like. I have Mitutoyo in the shop adn I would

    Larry Edgerton Today, 6:31 AM Go to last post
    Brent Cutshall

    Bowl carving question

    Hi Howard,
    The first thing I do is mark out the dimensions of the bowl on a cylinder shaped blank. You can choose whatever shape floats your boat.

    Brent Cutshall Today, 6:29 AM Go to last post
    Rich Riddle

    Is a Starrett a Starrett?

    Prashun, Fine Woodworking completed reviews a few years back and highly recommended the PEC squares for folks not wanting to spend tons of money on Starrett

    Rich Riddle Today, 6:24 AM Go to last post
    Lenore Epstein

    Old Habits

    Just because I feel like it, I don't want to rest my bench plane on its sole, but as a novice I frequently space out and try to lay it upside down before

    Lenore Epstein Today, 6:19 AM Go to last post
    Rich Riddle

    Incra metal stand, cleansweep worthwhile?

    I have both the stand and the clean sweep box and will try to properly load the pictures. The stand makes fabricating the box very easy. The box allows

    Rich Riddle Today, 6:16 AM Go to last post
  • Recent Blog Posts