Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Rabbit owners
Thread Starter: James Jaragosky
Please introduce yourself. If you could also put what model machine you have, and how long you have had it That would really help. My purpose in creating this thread is so we can help support each other, Because as you all know by now, factory support for everyday problems is limited. And there...
Last Post By: Dennis Watson Today, 9:36 AM

Your Best Nifty Shop Tip?
Thread Starter: Russell Neyman
It's the small things that often make the biggest difference. I've found that the crafty veterans seem to know a little trick here or there that make turning better, safer, faster, or easier. So I'm throwing out a challenge: give us your best "nifty" and when this thread is done, it will make a...
Last Post By: Rich Stewart Yesterday, 11:48 AM

Sharpening technique--removing the wire edge
Thread Starter: Steve Voigt
Hi all, This post may portray me as embarrassingly stupid and inefficient, but whatever. Here goes. For the last 15 years, regardless of the sharpening media, I have used the following method: 1) hone a secondary bevel on a coarse stone until I can feel the wire edge on the back, all the way...
Last Post By: george wilson Yesterday, 3:19 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: Craig Behnke Today, 9:33 AM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: John Champlain Yesterday, 11:58 AM

Lie Nielsen new waterstones
Thread Starter: Dave Cav
If didn't have a good set of Shapton pro stones I'd be looking at these. The combo stones appear to be a pretty good deal. http://www.lie-nielsen.com/catalog.php?sku=2-OHISHII
Last Post By: David Weaver Yesterday, 12:18 PM

Scott Lux

There is no available content written by Scott Lux

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

CAMaster Summer Specials

Deals and Discounts

(3 Viewing)
Contributor Announcements concerning
Mike Heidrick Today, 9:58 AM

Any updates on the Veritas shooting board plane?

Over on WoodNET there is a pic of a Veritas Chisel Plane.
Peter Pedisich Today, 9:57 AM

Lots of wood sad story

Hi,

I am relatively new to woodworking and this site. I hope this is the right place for this post.

I have been scouring CL
Chip Byrd Today, 9:52 AM

Any tips on removing a riciculously glued rubber tire from lower BS wheel?

GooGon, clean glue googon with water, then rubbing alcohol befor next adhesive
Mike Heidrick Today, 9:52 AM

Help building a Photostability Chamber

All good stuff, in my opinion.

I just do not understand all the brazing, welding and twisting, when you can buy the parts already made.
Stephen Cherry Today, 9:50 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Scott Lux

Recent Polls

Recent Forum Posts

Recent Blog Posts