Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Chinese laser purchase/Shenui/Laserworks tips and tricks thread
Thread Starter: Rodne Gold
Considering a lot of us are going or have gone that direction , I thought it a good idea to combine our knowledge pool in one thread. So I have started one. Those of you that have already posted to other threads can perhaps repeat and consolidate the posts here or at least point to other posts on...
Last Post By: Hermes Sandoval Today, 12:57 PM

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: Steve Fulgoni Yesterday, 10:44 PM

Vote For Your Favorite Baileigh Box Contest Entry
Thread Starter: Bill Wyko
Ok, we need some pictures. While many of you will be using lasers my friend Paul has a Chevalet. This tool was created in the late 1700's for production marquetry. It has a foot activated clamp to hold your stack of veneers and a "D" shaped saw that is held perpendicular to your cut but will move...
Last Post By: Bill Wyko Yesterday, 6:18 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: James White Today, 2:43 PM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: Jeff Woodcock Today, 12:04 PM

Memorial day must be coming....
Thread Starter: Jeff Monson
Unleaded went from $3.79 this morning to $4.09 in a matter of minutes. 30 cents is quite a hike, cant tell me the gas stations aren't smiling for a couple days.
Last Post By: Brian Elfert Yesterday, 11:26 PM

Mike Holbrook

There is no available content written by Mike Holbrook

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

Help building a Photostability Chamber

Prashun, have you tried a rheostat to regulate the intensity of the bulbs? What about a small fan to help uniformity of heat? I don't know what temperatures
Jeff Bartley Today, 3:26 PM

Gutter guards. Good or bad idea?

I have (17) very large maples on a corner residential lot and typically the gutters would fill with Buds in the spring, "Helicopters" in late
Mac McQuinn Today, 3:25 PM

Lie Nielsen 60 1/2 and Bronze RH skew block Plane

Bronze #140 is sold, 60 1/2 still available.

Harold, I'm sure they'll see your post
David Weaver Today, 3:20 PM

breaking the rules?

Post a pic and give us a lookie.Everybody liks ID this wood threads.At one of the wood supplers i go to they have three different woods they call mah.
Andrew Hughes Today, 3:19 PM

Funny Festool/Retailer Story...

Derek, Just curious: where are you located?
Jeff Bartley Today, 3:17 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Mike Holbrook

Recent Polls

Recent Forum Posts

Recent Blog Posts