• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Pat Barry

    Recommendation for new dovetail saw?

    Thread Starter: Pat Barry

    I want to get a new dovetail saw to replace my existing backsaw for dovetail cutting. The current saw is a standard backsaw (Pennsylvania Saw Corporation #78, 12ppi, 12" long, 3" deep). I also have another even larger backsaw and a Zona universal razor saw. I'd like something easier to control...

    Last Post By: Paul Saffold Yesterday, 10:21 PM Go to last post
    steven c newman

    Busy day today

    Thread Starter: steven c newman

    And now time for a few "Cold ones" First off, The Boss wanted a blind on the backdoor repaired with a new one.....New one needed those clips down at the bottom, to keep it from flopping around, used self-drilling drywall screws into the steel skin of the door...and had the driver tip drill into...

    Last Post By: steven c newman Today, 2:34 PM Go to last post
    Adam Less

    Dumb Question re: weight

    Thread Starter: Adam Less

    I have a 6040 Weike laser arriving in a couple of days. Because I have a door too small to bring the laser through, I have to remove a 4x6 window and bring the laser through that. With that said, the window is 33" off the ground and my intention is to uncrate the laser in the bed of my pick up...

    Last Post By: Dave Stevens-Vegas Yesterday, 5:26 PM Go to last post
    Mike Henderson

    Free SawStop Brake

    Thread Starter: Mike Henderson

    I was cutting a small piece of wood and before I knew it the blade was below the table and I had a small cut on my thumb. Don't even know exactly how everything happened. While the piece was small, I'd made the same cut many times before. Anyway, just a nick, bit of blood and a ruined...

    Last Post By: Joe Kaufman Today, 3:29 PM Go to last post
    Jeff Bartley

    Sharp chisels!

    Thread Starter: Jeff Bartley

    Sharp chisels yes! But not at the end, on the sides. I'm just wondering how many here have been cut up by the edges of their chisels? And does anyone purposely dull the side edges to prevent this? Jeff (with a slice on his index finger!)

    Last Post By: Patrick Chase Today, 2:41 PM Go to last post
    Michael Pyron

    Chisels

    Thread Starter: Michael Pyron

    yep, mighty useful tools. I'm at a point in my life where I feel the need to upgrade from the Buck Brother's chisels I've been getting from Home Depot... the issue I see, is that quality chisels have wooden handles, and I use a 12 oz. hammer. I know my hammer VERY well, and since I'm an in...

    Last Post By: Michael Pyron Today, 4:33 PM Go to last post
  • Steve Griffin

    There is no available content written by Steve Griffin
  • Recent Polls

    Which BMI are you? (Votes: 92)

    1. Underweight (Votes: 5)

    2. Normal (Votes: 31)

    3. Overweight (Votes: 26)

    4. Obese (Votes: 30)

  • Recent Forum Posts

    John K Jordan

    Wood identification

    Hard to tell from a picture of a single board. I've had some sections of cocobolo that looked that orange when cut although most is darker and has way

    John K Jordan Today, 5:01 PM Go to last post
    Michael Pyron

    Chisels

    please elucidate...

    I guess my ancient, out of production, Hart hammer is slightly domed...but one thing I do know is F=1/2mv^2...e.g. you

    Michael Pyron Today, 4:33 PM Go to last post
    Geoff Whaling

    2016 - new JET 1640EVS lathe

    While it is commendable to see manufacturers refreshing their product lines, I'm not convinced that the wider industry is really making much progress

    Geoff Whaling Today, 4:32 PM Go to last post
    Jim Koepke

    Chisels

    It may also be a matter of not wanting to carry more items in a tool box. The hammer has other uses. A mallet would require a space that may not be available.

    Jim Koepke Today, 4:31 PM Go to last post
    Ron Humphrey

    Wood identification



    I have two boards of this material. I cannot identiy it from my searches on the web. The picture is of a board 5" wide. The figuring

    Ron Humphrey Today, 4:31 PM Go to last post
  • Recent Blog Posts