Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Chinese laser purchase/Shenui/Laserworks tips and tricks thread
Thread Starter: Rodne Gold
Considering a lot of us are going or have gone that direction , I thought it a good idea to combine our knowledge pool in one thread. So I have started one. Those of you that have already posted to other threads can perhaps repeat and consolidate the posts here or at least point to other posts on...
Last Post By: Hermes Sandoval Today, 12:57 PM

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: Steve Fulgoni Yesterday, 10:44 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: James White Today, 5:24 PM

Vote For Your Favorite Baileigh Box Contest Entry
Thread Starter: Bill Wyko
Ok, we need some pictures. While many of you will be using lasers my friend Paul has a Chevalet. This tool was created in the late 1700's for production marquetry. It has a foot activated clamp to hold your stack of veneers and a "D" shaped saw that is held perpendicular to your cut but will move...
Last Post By: Bill Wyko Yesterday, 6:18 PM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: John Champlain Today, 5:57 PM

Memorial day must be coming....
Thread Starter: Jeff Monson
Unleaded went from $3.79 this morning to $4.09 in a matter of minutes. 30 cents is quite a hike, cant tell me the gas stations aren't smiling for a couple days.
Last Post By: Brian Elfert Yesterday, 11:26 PM

frank shic

There is no available content written by frank shic

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

sizing dessicant dryer for spray finishing

Andy, I can't speak to the dessicant dryer but you may not need one. If you can cool the air before the gun the water will condense out and you won't
Steve Jenkins Today, 6:01 PM

Overstrike (ghosting) Problem

Ever find out what the problem is/was ??
Mark Sipes Today, 5:59 PM

Respirator Question

I like the 3M 7500 with the organic cartridges also. Works effectively with all that I have sprayed, even pre-cat lacquer. When not in use, store them
Alan Lightstone Today, 5:57 PM

Laser Engraving True 8bit Shades of Grey

Hello group,
I am a friend of Jeff's, and at his urging have recently joined this forum and have been monitoring this thread. Like Jeff, I also
John Champlain Today, 5:57 PM

Any updates on the Veritas shooting board plane?

Shop made hot dog changed my comfort and confidence levels with my LV LAJ.

.
glenn bradley Today, 5:51 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

frank shic

Recent Polls

Recent Forum Posts

Recent Blog Posts