Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Rabbit owners
Thread Starter: James Jaragosky
Please introduce yourself. If you could also put what model machine you have, and how long you have had it That would really help. My purpose in creating this thread is so we can help support each other, Because as you all know by now, factory support for everyday problems is limited. And there...
Last Post By: Dennis Watson Today, 2:47 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: James White Today, 10:22 AM

Any updates on the Veritas shooting board plane?
Thread Starter: Scott Stafford
I thought it best to check to see if anyone has heard of any progress on the Veritas shooting board plane. Timeline? Features? I'm ready to buy a Lie-Nielsen 51 but thought it best to see what anyone had read or heard lately of the unofficially announced Veritas. I might be able to...
Last Post By: Brad Simmons Today, 9:44 PM

A Scientist Explains The Physics of Resawing
Thread Starter: Julie Moriarty
I don't know he's a scientist...:rolleyes:
Last Post By: Metod Alif Today, 8:34 AM

How Do You Make This Cut?
Thread Starter: Julie Moriarty
Cut offs were clamped in place to show the "before" state. I've been confronted with this type of thing many times, tight conditions, you can't take it into the shop, no small plunge cut saw, etc. And you don't want a huge mess because you're working in a lived-in area. In this case, the...
Last Post By: Art Mann Today, 2:02 PM

The whats on your bench besides sharpening stones thread
Thread Starter: Chris Griggs
Hi friends, Wow, as I write this the top three thread on the forum are about sharpening. As one of the main perpetrators of sharpening discussions that go on and on and on....and on....etc... I feel it is my duty to start a thread about something other than sharpening stones. So here's...
Last Post By: Steve Voigt Today, 9:55 PM

Bryan Morgan

There is no available content written by Bryan Morgan

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

BU angle

low 30s bevel angle is the lowest you'll get A2 around 60-62 hardness to not have small chipouts, meaning the edge will fail only from wear.

Derek Cohen Today, 10:23 PM

Strange laser alignment issue

I have attached a diagram with mirrors before the brewster window. The mirrors 1(near field) and 2(far field) are used to align the beam path for the
Mike Lysov Today, 10:23 PM

Need an electrical engineer

I don't really know what's what when it comes to audio equipment, but it sounds like you've connected a high pass filter to the output of a signal generator.
Bob Coleman Today, 10:22 PM

12 inch table saw blades

I like the Amana A.G.E blades. IMO, they're a great value.
johnny means Today, 10:20 PM

Powermatic 90 bowl lathe - I want biggerer!

Very nice work there Lee. I applaud your desire to build something rather than buy off the rack by plunking down the ole' Visa card.

I agree
Olaf Vogel Today, 10:19 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Bryan Morgan

Recent Polls

Recent Forum Posts

Recent Blog Posts