• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Jerome Stanek

    Glowforge release

    Thread Starter: Jerome Stanek

    I was wondering if Glowforge has sent out any units yet. I thought they were supposed to release the middle of December.

    Last Post By: Dave Sheldrake Today, 10:14 AM Go to last post
    Mike Heidrick

    Pole Barn 40X64X16

    Thread Starter: Mike Heidrick

    Signed a contract yesterday with S&L Builders out of Indiana for a 40X64X16 Pole Barn with a 10X24 porch. Build date August 18, 2014. Plan to install Pex for raidant floor heat. Concrete slab 5" thick. Also doing 1.5" closed cell foam under the pad. Built on Laminated posts in ground. Will...

    Last Post By: Mike Heidrick Today, 1:21 AM Go to last post
    Stanley Covington

    The Essential Oilpot

    Thread Starter: Stanley Covington

    The oilpot is an essential tool for precision woodworking. I first learned this fact while living in Japan when I was called a fool by a joiner for not having one in my tool kit. I won't bore you with that embarrassing story, but a quick tutorial on oilpots as I understand them may be useful. ...

    Last Post By: george wilson Today, 8:45 AM Go to last post
    Tim Bridge

    Making a Living Woodworking

    Thread Starter: Tim Bridge

    Is it possible to make a living woodworking out of my garage making small projects and selling them at flea markets or other places? I have a bandsaw, router table, planer, miter saw, table saw, spindle sander, drill press and an assortment of hand tools. I am tired or working for electrical...

    Last Post By: Martin Wasner Yesterday, 6:34 PM Go to last post
    Brian Kent


    Thread Starter: Brian Kent

    Just glad I had that steady rest to that if I had a catch it wouldn't pry the bank loose. In this case I barely touched the rim with the tip of a v scraper. On the end of the 10" chalice, the physics works against me. I have a whole lot of long work to do (23 more chalices 10" x 3.5") so I...

    Last Post By: Stan Smith Yesterday, 5:16 PM Go to last post
    Dan Schmidt

    Slider Questions

    Thread Starter: Dan Schmidt

    1 - for those of you who use sliders to rip 4x8 sheets, is such a support on the sliding bed necessary (shown here with red arrow) to support the back left corner of the sheet? 2 - for those of you with Felder units specifically, do you have the new swing-away overhead blade guard as shown...

    Last Post By: Brian Lamb Yesterday, 11:38 AM Go to last post
  • Bob Germond

    There is no available content written by Bob Germond
  • Recent Polls

    Which vice for sawing (Votes: 30)

    1. Face vice (Votes: 13)

    2. Moxxon vice (Votes: 13)

    3. Other (Votes: 4)

  • Recent Forum Posts

    Mike Cutler

    Festool TS-75


    I own the TS75, like others, and will tell you that it is one very nice tool. I needed to cut a 17'x3'x2 1/2" thick slab of Padauk,

    Mike Cutler Today, 10:17 AM Go to last post
    Dave Sheldrake

    Glowforge release

    yup, companies are making clones of the Redsail X700 in the same colours using whatever parts are around at the time, those and the K40 are the source

    Dave Sheldrake Today, 10:14 AM Go to last post
    Robert Willing

    Three firsts

    Thanks all for your comments or lack of same. I posted this on a Router Forum and got 20 comments.

    Robert Willing Today, 10:09 AM Go to last post
    Lee DeRaud

    Glowforge release

    Eh? I was under the impression the eBay/Paypal policies boiled down to, you only have to get it back to the seller..."shipped from USA" implies

    Lee DeRaud Today, 9:57 AM Go to last post
    Don Corbeil

    Options for laser power meters

    Scott, welcome to the forum!
    I haven't yet looked up your given source, but for me, I want the tool the works best for the job whether it be a

    Don Corbeil Today, 9:53 AM Go to last post
  • Recent Blog Posts