Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Chinese laser purchase/Shenui/Laserworks tips and tricks thread
Thread Starter: Rodne Gold
Considering a lot of us are going or have gone that direction , I thought it a good idea to combine our knowledge pool in one thread. So I have started one. Those of you that have already posted to other threads can perhaps repeat and consolidate the posts here or at least point to other posts on...
Last Post By: Khalid Nazim Today, 3:40 PM

Your Best Nifty Shop Tip?
Thread Starter: Russell Neyman
It's the small things that often make the biggest difference. I've found that the crafty veterans seem to know a little trick here or there that make turning better, safer, faster, or easier. So I'm throwing out a challenge: give us your best "nifty" and when this thread is done, it will make a...
Last Post By: Russell Neyman Yesterday, 7:18 PM

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: Roy Turbett Yesterday, 8:22 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: James White Today, 8:18 AM

BBQ advice needed
Thread Starter: Rick Potter
I just finished looking at old threads about BBQ's. The weber seemed to be the choice in '05/'06. Is this still the case, or is there a new best choice? I just need a basic, medium size gas BBQ that runs on natural gas. I think I want stainless burners and grates, since I have had problems...
Last Post By: Neal Daughtry Today, 5:30 PM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: Jeff Woodcock Yesterday, 6:08 PM

Todd Burch

There is no available content written by Todd Burch

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

Help building a Photostability Chamber

yeah, size is a big factor. Rather than making the new one with plywood, make it with insulated panels, aka Plywood/insulation/plywood sandwiches. Make
John Sanford Today, 5:35 PM

Sharpening technique--removing the wire edge

He was incredible, wasn't he? Everyone says, "Oh, Tiger makes it look easy" or someone else makes it look easy. LOL. Tiger makes it look
John Coloccia Today, 5:33 PM

Wearing out waterstones...

It's an experience thing, you decide whatever pleases you. Some people flatten heavily and often. But with experience, you'll find that you don't need
David Weaver Today, 5:31 PM

BBQ advice needed

Those who like charcoal grilling should check out the Portable Kitchen http://www.pkgrills.com/index.php I have one that was handed down to me from my
Neal Daughtry Today, 5:30 PM

Beam reflection when cutting metals

Dan, I have just sent you a personal message.
Mike Lysov Today, 5:28 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Todd Burch

Recent Polls

Recent Forum Posts

Recent Blog Posts