Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: robert baccus Today, 1:11 AM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: David Kumm Today, 11:11 AM

BBQ advice needed
Thread Starter: Rick Potter
I just finished looking at old threads about BBQ's. The weber seemed to be the choice in '05/'06. Is this still the case, or is there a new best choice? I just need a basic, medium size gas BBQ that runs on natural gas. I think I want stainless burners and grates, since I have had problems...
Last Post By: Rick Potter Yesterday, 5:08 PM

Pterocarpus Rex drum set
Thread Starter: Seth Dolcourt
Hi, Creekers, Back for another drum project. This one's gonna be big. And, it will take a while. Pterocarpus is the genus for the market name of padauk, and Pterocarpus Rex is a play on T Rex. This is a collaboration with a guy who will finish, drill and deliver the drums to his own...
Last Post By: Mark Crenshaw Today, 11:10 AM

Old plane blade too hard?
Thread Starter: Shaun Mahood
I've got an old wooden jointer plane with a blade that I have never been able to sharpen satisfactorily. I just bought a bench grinder and have given it another try. It seemed to take longer to grind than my other blades, and after that is taking much more time and effort to sharpen on my stones. I...
Last Post By: Steve Voigt Yesterday, 7:16 PM

A Scientist Explains The Physics of Resawing
Thread Starter: Julie Moriarty
I don't know he's a scientist...:rolleyes:
Last Post By: Matt Day Today, 8:26 AM

Barry Stratton

There is no available content written by Barry Stratton

Recent Polls
If you use clamp-together dust duct do you feel the money was well spent? (1 Votes)

What brand did you buy? (1 Votes)

Are you aware of any other brand that is interchangeable with it? (0 Votes)
Recent Forum Posts

flooring mill 2nd's worth the work ?

Anyone get the chance to work with 2nd's from Hardwood flooring mills ? Found a place that has Maple, Walnut, Birch , Beech, Cherry
Clarence Martin Today, 4:14 PM

First Real Hollowform

Wes, congrats on just keeping it together and wisely choosing the 80 grit gouge to deal with the tearout. Some neat looking curl in that stuff, glad
Tim Rinehart Today, 4:09 PM

Flow rate on water well?

Probably not.
Flow is equal to the square root of the D/P across an orifice restriction, or system. You would be close to the nominal if you could
Mike Cutler Today, 4:08 PM

Going Pro

Many of the best moments of my life were without a penny in my pockets.

jtk
Jim Koepke Today, 4:05 PM

Problem Lining up Dominos

With the dominplate you use the domino upside down so the only registration mark you have is scored on the bottom of the domino.I am using a 4 mm bit
fRED mCnEILL Today, 4:00 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Barry Stratton

Recent Polls

Recent Forum Posts

Recent Blog Posts