• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Jerome Stanek

    Glowforge release

    Thread Starter: Jerome Stanek

    I was wondering if Glowforge has sent out any units yet. I thought they were supposed to release the middle of December.

    Last Post By: Bill George Today, 8:04 AM Go to last post
    Mike Heidrick

    Pole Barn 40X64X16

    Thread Starter: Mike Heidrick

    Signed a contract yesterday with S&L Builders out of Indiana for a 40X64X16 Pole Barn with a 10X24 porch. Build date August 18, 2014. Plan to install Pex for raidant floor heat. Concrete slab 5" thick. Also doing 1.5" closed cell foam under the pad. Built on Laminated posts in ground. Will...

    Last Post By: Mike Heidrick Today, 1:21 AM Go to last post
    Stanley Covington

    The Essential Oilpot

    Thread Starter: Stanley Covington

    The oilpot is an essential tool for precision woodworking. I first learned this fact while living in Japan when I was called a fool by a joiner for not having one in my tool kit. I won't bore you with that embarrassing story, but a quick tutorial on oilpots as I understand them may be useful. ...

    Last Post By: george wilson Today, 8:25 AM Go to last post
    Tim Bridge

    Making a Living Woodworking

    Thread Starter: Tim Bridge

    Is it possible to make a living woodworking out of my garage making small projects and selling them at flea markets or other places? I have a bandsaw, router table, planer, miter saw, table saw, spindle sander, drill press and an assortment of hand tools. I am tired or working for electrical...

    Last Post By: Martin Wasner Yesterday, 6:34 PM Go to last post
    Brian Kent

    Oops

    Thread Starter: Brian Kent

    Just glad I had that steady rest to that if I had a catch it wouldn't pry the bank loose. In this case I barely touched the rim with the tip of a v scraper. On the end of the 10" chalice, the physics works against me. I have a whole lot of long work to do (23 more chalices 10" x 3.5") so I...

    Last Post By: Stan Smith Yesterday, 5:16 PM Go to last post
    Dan Schmidt

    Slider Questions

    Thread Starter: Dan Schmidt

    1 - for those of you who use sliders to rip 4x8 sheets, is such a support on the sliding bed necessary (shown here with red arrow) to support the back left corner of the sheet? 2 - for those of you with Felder units specifically, do you have the new swing-away overhead blade guard as shown...

    Last Post By: Brian Lamb Yesterday, 11:38 AM Go to last post
  • willie sobat

    There is no available content written by willie sobat
  • Recent Polls

    Which vice for sawing (Votes: 30)

    1. Face vice (Votes: 13)

    2. Moxxon vice (Votes: 13)

    3. Other (Votes: 4)

  • Recent Forum Posts

    Bud Millis

    Creeker's Weekend Accomplishments

    Also got to test out the shop made 3 in 1 faux Dremel base. Here I am routing the bottom brace pockets for a guitar build. Its actually a Craftsman Rotary

    Bud Millis Today, 8:27 AM Go to last post
    Bill George

    needing help

    You need to also post the part number of the controller card to find out about that warning light. Plus the fact the tube will only fire with the test

    Bill George Today, 8:27 AM Go to last post
    Jon Endres

    Need Recommendations for TS Blades

    For ripping, I have a Freud LM74R010 30 Tooth TCG Glue Line Rip blade. I don't use it very often unless I have large quantities to rip - one or two boards

    Jon Endres Today, 8:26 AM Go to last post
    george wilson

    The Essential Oilpot

    Turpentine(the REAL STUFF,WHICH IS GETTING VERY HARD TO FIND),and says "From the living pine" on the can,will harden into a hard film on your

    george wilson Today, 8:25 AM Go to last post
    mark kosse

    Unique Swan drawknife

    Like this Jim? My current project. My wife is slinging the draw knife though.

    I have to find my camera

    mark kosse Today, 8:18 AM Go to last post
  • Recent Blog Posts