Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: robert baccus Today, 1:11 AM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: David Kumm Today, 11:11 AM

Pterocarpus Rex drum set
Thread Starter: Seth Dolcourt
Hi, Creekers, Back for another drum project. This one's gonna be big. And, it will take a while. Pterocarpus is the genus for the market name of padauk, and Pterocarpus Rex is a play on T Rex. This is a collaboration with a guy who will finish, drill and deliver the drums to his own...
Last Post By: Mark Crenshaw Today, 11:10 AM

Old plane blade too hard?
Thread Starter: Shaun Mahood
I've got an old wooden jointer plane with a blade that I have never been able to sharpen satisfactorily. I just bought a bench grinder and have given it another try. It seemed to take longer to grind than my other blades, and after that is taking much more time and effort to sharpen on my stones. I...
Last Post By: Steve Voigt Yesterday, 7:16 PM

Memorial day must be coming....
Thread Starter: Jeff Monson
Unleaded went from $3.79 this morning to $4.09 in a matter of minutes. 30 cents is quite a hike, cant tell me the gas stations aren't smiling for a couple days.
Last Post By: Rick Potter Today, 6:09 PM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: Michael Hunter Today, 5:33 PM

Reed Gray

There is no available content written by Reed Gray

Recent Polls
If you use clamp-together dust duct do you feel the money was well spent? (1 Votes)

What brand did you buy? (1 Votes)

Are you aware of any other brand that is interchangeable with it? (0 Votes)
Recent Forum Posts

Silver Mist Hardtail Strat

Thanks Bill! It's not for sale so you're safe.

The radius is 9.5". Last year I built a swing arm belt sander that does the job rather
Mark Crenshaw Today, 6:10 PM

Memorial day must be coming....

I always try to get mine at Costco. It's usually as cheap as anywhere, and I get an additional 3% off for using the Costco AMEX. At $4 per gallon, that's
Rick Potter Today, 6:09 PM

Lie Nielsen new waterstones

Without going too deeply into polishing esoterica (and for some us, erotica), I agree, although I'd say deleterious to the edge rather than to the hardened
David Barnett Today, 6:06 PM

Problem Lining up Dominos

I have used a domino for plywood case assembly since the product was first released - I have used about 2,500 5mm domino's since then (about 2/3 through
Erik Christensen Today, 6:05 PM

Waterlox smell

>>>> If I do that, will it change the appearance of the Waterlox?

>>>> If I do that, will it change the appearance
Howard Acheson Today, 6:05 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Reed Gray

Recent Polls

Recent Forum Posts

Recent Blog Posts