• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Pat Barry

    Recommendation for new dovetail saw?

    Thread Starter: Pat Barry

    I want to get a new dovetail saw to replace my existing backsaw for dovetail cutting. The current saw is a standard backsaw (Pennsylvania Saw Corporation #78, 12ppi, 12" long, 3" deep). I also have another even larger backsaw and a Zona universal razor saw. I'd like something easier to control...

    Last Post By: Paul Saffold Yesterday, 10:21 PM Go to last post
    steven c newman

    Busy day today

    Thread Starter: steven c newman

    And now time for a few "Cold ones" First off, The Boss wanted a blind on the backdoor repaired with a new one.....New one needed those clips down at the bottom, to keep it from flopping around, used self-drilling drywall screws into the steel skin of the door...and had the driver tip drill into...

    Last Post By: steven c newman Today, 2:34 PM Go to last post
    Adam Less

    Dumb Question re: weight

    Thread Starter: Adam Less

    I have a 6040 Weike laser arriving in a couple of days. Because I have a door too small to bring the laser through, I have to remove a 4x6 window and bring the laser through that. With that said, the window is 33" off the ground and my intention is to uncrate the laser in the bed of my pick up...

    Last Post By: Dave Stevens-Vegas Yesterday, 5:26 PM Go to last post
    Jeff Bartley

    Sharp chisels!

    Thread Starter: Jeff Bartley

    Sharp chisels yes! But not at the end, on the sides. I'm just wondering how many here have been cut up by the edges of their chisels? And does anyone purposely dull the side edges to prevent this? Jeff (with a slice on his index finger!)

    Last Post By: Patrick Chase Today, 2:41 PM Go to last post
    Mike Henderson

    Free SawStop Brake

    Thread Starter: Mike Henderson

    I was cutting a small piece of wood and before I knew it the blade was below the table and I had a small cut on my thumb. Don't even know exactly how everything happened. While the piece was small, I'd made the same cut many times before. Anyway, just a nick, bit of blood and a ruined...

    Last Post By: Andrew Joiner Today, 2:47 PM Go to last post
    Michael Pyron


    Thread Starter: Michael Pyron

    yep, mighty useful tools. I'm at a point in my life where I feel the need to upgrade from the Buck Brother's chisels I've been getting from Home Depot... the issue I see, is that quality chisels have wooden handles, and I use a 12 oz. hammer. I know my hammer VERY well, and since I'm an in...

    Last Post By: Clay Parrish Today, 3:12 PM Go to last post
  • Tom Sherman

    There is no available content written by Tom Sherman
  • Recent Polls

    Which BMI are you? (Votes: 92)

    1. Underweight (Votes: 5)

    2. Normal (Votes: 31)

    3. Overweight (Votes: 26)

    4. Obese (Votes: 30)

  • Recent Forum Posts

    Clay Parrish


    Mm...I say have more faith in your adaptability and use the right tool for the job - a wooden mallet. There's no reason you have to use the same hammer

    Clay Parrish Today, 3:12 PM Go to last post
    Michael Pyron


    schweet...thx for that tip...I notice they have plastic handled Two Cherries chisels there...

    the link I gave does look very similar to Two

    Michael Pyron Today, 3:04 PM Go to last post
    Patrick Chase


    Those Bucks are actually not horrible chisels once tuned up properly, especially considering the price. I have a 3/4 that I use as a "beater"

    Patrick Chase Today, 3:03 PM Go to last post
    Mark Gibney

    Storing Glue

    I just bought a couple of gallons of Multibond 2000 glue from a friend who had a 5 gallon bucket. This amount might last me only a year, but might last

    Mark Gibney Today, 2:55 PM Go to last post
    Rahul Srivastava

    Protecting Cast Iron for long term storage (4 years) in garage without Boeshield

    Doug, Thanks for the feedback. I live in Edmonton Alberta Canada. I don't really know how to describe the humidity level. We have all 4 seasons here.

    Rahul Srivastava Today, 2:47 PM Go to last post
  • Recent Blog Posts