Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Chinese laser purchase/Shenui/Laserworks tips and tricks thread
Thread Starter: Rodne Gold
Considering a lot of us are going or have gone that direction , I thought it a good idea to combine our knowledge pool in one thread. So I have started one. Those of you that have already posted to other threads can perhaps repeat and consolidate the posts here or at least point to other posts on...
Last Post By: George Carlson Today, 9:07 AM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: Mike Null Today, 6:21 AM

BBQ advice needed
Thread Starter: Rick Potter
I just finished looking at old threads about BBQ's. The weber seemed to be the choice in '05/'06. Is this still the case, or is there a new best choice? I just need a basic, medium size gas BBQ that runs on natural gas. I think I want stainless burners and grates, since I have had problems...
Last Post By: Neal Daughtry Yesterday, 5:30 PM

Sharpening technique--removing the wire edge
Thread Starter: Steve Voigt
Hi all, This post may portray me as embarrassingly stupid and inefficient, but whatever. Here goes. For the last 15 years, regardless of the sharpening media, I have used the following method: 1) hone a secondary bevel on a coarse stone until I can feel the wire edge on the back, all the way...
Last Post By: David Weaver Today, 8:33 AM

How about a little side contest? Make a Pencil sharpener...
Thread Starter: David Weaver
The catch being, make it completely and totally by hand. No electric at all with the possible exception of drilling a hole in the cutter. In the world of everything being sharp working better, I'm thinking that those little hand twist manual sharpeners would work pretty well if the cutter in them...
Last Post By: Jon Shank Yesterday, 11:43 PM

Buy versus build?
Thread Starter: Jamie Buxton
Because we're builders, we can make stuff for our shops. We also have manufacturers which are happy to sell us similar stuff. For instance, you can make your own sawhorses, or you can buy them. You can make a workbench, or you can buy one. You can make your own jigs (for instance a shelf-pin...
Last Post By: Jim Becker Yesterday, 4:57 PM

Randal Stevenson

There is no available content written by Randal Stevenson

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

Silver Mist Hardtail Strat

Hey, Mark. All you have to do is set each arm at the length you want.
John Coloccia Today, 9:49 AM

Silver Mist Hardtail Strat

Mark....Did you modify the headstock shape? I'm sure you know that Fender gets all worked up when you place your logo on their headstock shape. They defend
Greg Savage Today, 9:35 AM

WTB 3520A Banjo

I'm looking for a used one if anyone has one laying around from upgrading to the 3520B.PM if you have one.

Chris
Chris Woodall Today, 9:27 AM

Powermatic 90 bowl lathe - I want biggerer!

Thanks for the encouragement

Mike - why would I go anything other than my hammered green? I know you did for your behemoth, but I'm
Lee Alkureishi Today, 9:21 AM

New to the Forum

...and I must remember to not stand too closely to those spontaneously-combusting percussionists!
Edward Mitton Today, 9:19 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Randal Stevenson

Recent Polls

Recent Forum Posts

Recent Blog Posts