• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Hasin Haroon

    Veritas Shooting Plane quite a bit out of square. How important is this?

    Thread Starter: Hasin Haroon

    Allow me to preface this post by saying this is not meant to be a post hating on Veritas tools or their commitment to quality at all - I have purchased almost all of the planes they offer (I'm not particularly affluent, so this means I need to save up/sell other tools to be able to afford them) and...

    Last Post By: Tony Zaffuto Today, 3:06 PM Go to last post
    Jefferey Scott

    Oklahoma Homestead 40x80x12

    Thread Starter: Jefferey Scott

    Hey guys, I'm in the early planning stages for a workshop that will be used as both a woodworking shop and a metal fabrication shop. I'm trying to figure out how much lighting I can afford to put in and have a rough floorplan with 21 - 4 foot 4 bulb high bay fluorescent fixtures (at about $60 a...

    Last Post By: Jefferey Scott Today, 6:59 AM Go to last post
    Greg Parrish

    New Laguna lathe

    Thread Starter: Greg Parrish

    Received my new 18/36 today. OMG it is so much better than the Nova Comet, and I know that isn't a fair comparison, but it is amazing the difference in experience the extra power makes. I have some fine tuning to do on the layout, location, etc but it's a start. I'll be building a sand box for it...

    Last Post By: Roger Chandler Today, 10:39 AM Go to last post
    Jason Zondor

    Woodshop Build

    Thread Starter: Jason Zondor

    Hello, Finally to the point where I can start working on my wood shop. Feel free to offer up comments and ideas... This is a hobby is therapeutic for me and I don't mind criticism. Plus, I know that there are a lot more talented people that I can learn from. The goal for the wood shop is a...

    Last Post By: Jim Becker Today, 11:35 AM Go to last post
    mark mcfarlane

    Yet another shop build.... McFarlane

    Thread Starter: mark mcfarlane

    After a 9 month battle with the local water district over an easement, we started clearing the land for my new shop today. It was amazing to watch these guys clear the land. We had three 80-100' pine trees removed and about a dozen smaller ones. One of the tall trees was 2 feet off my...

    Last Post By: Malcolm McLeod Today, 10:18 AM Go to last post
    Adam Gerlach

    Please help with my TS blade sharpening nightmare!

    Thread Starter: Adam Gerlach

    I recently helped a fired do a project, and because no good deed goes unpunished, I nipped the head of a brad nail with my WWII ( despite my friend's claim that the wood was clean.) I inspected the blade and the carbide looked fine, but it was dull. I couldn't even cut a pine 2x4. I usually send...

    Last Post By: Ole Anderson Today, 10:22 AM Go to last post
  • john lampros

    There is no available content written by john lampros
  • Recent Polls

    Your favorite new production bench chisel (Votes: 84)

    1. Lie Nielsen (Votes: 34)

    2. Lee Valley PM-V11 (Votes: 23)

    3. Lee Valley O1 (Votes: 1)

    4. MHG (Votes: 2)

    5. Two Cherries Hirsch (Votes: 2)

    6. Stubai (Votes: 1)

    7. Pfeil (Votes: 3)

    8. Sorby (new production) (Votes: 1)

    9. Stanley sweetheart (new production) (Votes: 6)

    10. Ashley Iles (Votes: 11)

  • Recent Forum Posts

    Roger Chandler

    Well, I finally did it.

    Congrats on the new G0766, Bill! Pics are always in order! Lots of great help and info on the Grizzly Green Monster Group [GGMG]. Feel free to join

    Roger Chandler Today, 7:16 PM Go to last post
    Brice Rogers

    Knockout bar

    Do you have to drill the entire length of the spindle or just the chuck end? If it is the entire length, give some thought on how you are going to keep

    Brice Rogers Today, 7:05 PM Go to last post
    mike klein

    Engravelab Version 8 Needed

    Anyone have version 8 of Engravelab they are wanting to get rid of. I have version 9.1 but a couple of the features in it are not working properly with

    mike klein Today, 6:52 PM Go to last post
    Mel Fulks

    What spacing between boards on a deck?

    Plywood sloped at least 1/8 per foot and covered with glued canvas ,then painted. Lasts a very long time ,like the same treatment with boards used to.

    Mel Fulks Today, 6:46 PM Go to last post
    Mike V Miller

    Mirror replacement upgrade

    Thanks John. Been running this machine for 2 years and think it's time to upgrade .

    Mike V Miller Today, 6:40 PM Go to last post
  • Recent Blog Posts