Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: robert baccus Today, 1:11 AM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: David Kumm Today, 11:11 AM

BBQ advice needed
Thread Starter: Rick Potter
I just finished looking at old threads about BBQ's. The weber seemed to be the choice in '05/'06. Is this still the case, or is there a new best choice? I just need a basic, medium size gas BBQ that runs on natural gas. I think I want stainless burners and grates, since I have had problems...
Last Post By: Rick Potter Yesterday, 5:08 PM

Pterocarpus Rex drum set
Thread Starter: Seth Dolcourt
Hi, Creekers, Back for another drum project. This one's gonna be big. And, it will take a while. Pterocarpus is the genus for the market name of padauk, and Pterocarpus Rex is a play on T Rex. This is a collaboration with a guy who will finish, drill and deliver the drums to his own...
Last Post By: Mark Crenshaw Today, 11:10 AM

Old plane blade too hard?
Thread Starter: Shaun Mahood
I've got an old wooden jointer plane with a blade that I have never been able to sharpen satisfactorily. I just bought a bench grinder and have given it another try. It seemed to take longer to grind than my other blades, and after that is taking much more time and effort to sharpen on my stones. I...
Last Post By: Steve Voigt Yesterday, 7:16 PM

A Scientist Explains The Physics of Resawing
Thread Starter: Julie Moriarty
I don't know he's a scientist...:rolleyes:
Last Post By: Matt Day Today, 8:26 AM

James Conrad

There is no available content written by James Conrad

Recent Polls
If you use clamp-together dust duct do you feel the money was well spent? (1 Votes)

What brand did you buy? (1 Votes)

Are you aware of any other brand that is interchangeable with it? (0 Votes)
Recent Forum Posts

Electromagnetic pendulum clock

The front portion of the clock is done.

The second had shaft rides on bearings front and back, and actually passes through the center
Dick Bipes Today, 1:01 PM

Shop built Mallet

Good thing I went back and read that a second time. The first time I read it as "whacking my foe."
Michael Ray Smith Today, 12:58 PM

Shop built Mallet

Well it is just a moment.

As you get older you have moments of lucidity.

We call those "junior moments."
Jim Koepke Today, 12:55 PM

Not Enough Fingers to Count the Mistakes

I'm with you, Jim... While I believe that we should love what we do for a living (and I do), woodworking for me is peaceful relaxation and escape from
Jim Neeley Today, 12:54 PM

outfeed table top

I have a Grizzly G0623X and it does have a slightly larger footprint inside the shop. I need to get some more additional surfaces for doing assembly
Matt Mackinnon Today, 12:46 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

James Conrad

Recent Polls

Recent Forum Posts

Recent Blog Posts