Tab Content
No Recent Activity

7 Visitor Messages

  1. View Conversation
    Happy, Happy Birthday Dan! Eat cake!
  2. View Conversation
    Hi Dan do you use the photograv software ?
  3. View Conversation
    Dan, someone posted a message that you might be interested in engraving a gift plaque. A friend of mine would like this done. She lives in Kensington, Md. It's an engraving from a line drawing, an image of a cross. If you are interested, pm me back with contact information she can use.

    Thanks,
    Larry Klaaren
  4. View Conversation
    Hey thanks for the help Dan it's very useful. A lot easier then wasting a bunch of material and teaching myself.
    Chad Paulsen
  5. View Conversation
    Dan, Have you dabble in leds for autos, with this plexi job he email me inquring about under car lighting. Also what is your process for kerf adjustment??
  6. View Conversation
    Hi Dan,
    I am about to buy a us-cutter. How do you like your cutter? I have a job comming up an need to cut heat transfer vinyl for polyester. I am looking at the P Cut, can these cutters cut it. I ck on maxium thickness an think it might be wrong. Can you please email me @ pnscrystals@aol.com
    Thank you
    SAL SHEPHERD
  7. View Conversation
    Hi Dan,
    About the CVT; I don't think it's going to be a problem. Before I bought the Nissan I checked out some of the owner forums. One guy from Canada did a lot of miles under arduous conditions and was concerned about the state of the CVT. Apparently the CVT has a computer chip that logs conditions and allocates a score for each cold start/hard accel/manual shift etc, and can be read by the dealer for service purposes. He had it checked and the score was way below a service requirement despite the hard use and harsh environment. I can't remember the figures, but his result seemed to indicate the motor would go out well before the CVT.
    I understand that if you abuse the CVT with burnouts it will overheat and go into 2nd gear only limp-home mode, but they seem to be pretty robust.

    Bob Davis
Showing Visitor Messages 1 to 7 of 7
About Dan Hintz

Basic Information

Date of Birth
August 12, 1972 (45)
About Dan Hintz
Location:
Glenelg, MD
Interests:
LEDs and cars
Occupation:
Electrical Engineer

Signature


Hi-Tec Designs, LLC -- Owner (and self-proclaimed LED guru )

Trotec 80W Speedy 300 laser w/everything
CAMaster Stinger CNC (25" x 36" x 5")
USCutter 24" LaserPoint Vinyl Cutter
Jet JWBS-18QT-3 18", 3HP bandsaw
Robust Beauty 25"x52" wood lathe w/everything
Jet BD-920W 9"x20" metal lathe
Delta 18-900L 18" drill press

Flame Polisher (ooooh, FIRE!)
Freeware: InkScape, Paint.NET, DoubleCAD XT
Paidware: Wacom Intuos4 (Large), CorelDRAW X5

Statistics


Total Posts
Total Posts
12,261
Posts Per Day
3.36
Visitor Messages
Total Messages
7
Most Recent Message
08-12-2010 8:40 AM
General Information
Last Activity
06-08-2016 7:30 AM
Join Date
11-26-2007
Home Page
http://www.Hi-TecDesigns.com

5 Friends

  1. Dan Park Dan Park is offline

    Member

    • Send a message via Yahoo to Dan Park
    Dan Park
  2. Joe Aliperti Joe Aliperti is offline

    Member

    Joe Aliperti
  3. Mike Lassiter Mike Lassiter is offline

    Member

    Mike Lassiter
  4. Philip Kulp Philip Kulp is offline

    Member

    Philip Kulp
  5. Primvs Aebvtivs Primvs Aebvtivs is offline

    Member

    Primvs Aebvtivs
Showing Friends 1 to 5 of 5
View Dan Hintz's Blog

Recent Entries

DIY air filtration unit for <$200

by Dan Hintz on 02-21-2013 at 1:29 PM
I thought I would add this to my blog since so many have asked about it in the past (and it takes me a while to find it again):

Quote Originally Posted by Dan Hintz View Post
As payback to the lasering community, I'm sharing my "plans" (such as they are) for everyone to copy. Well, not so much "plans" as pictures of the completed unit, but it should be obvious how to recreate something similar.

Due to poor planning on my part and a lack of any real sleep, I made one or two errors in the construction

Read More

Categories
Uncategorized