5 Attachment(s)
Grizzly G0651 Tablesaw Arrives
Grizzly G0651 Tablesaw Inspection Report
with photos
I have been building furniture off and on for 25 years using hand planes and a Sears tablesaw. I have wanted a cabinet saw and a jointer for a long time, but kept putting it off. I finally decided on the Grizzly G0490 Joiner and the G0651 Tablesaw. I choose Grizzly because of what people here have said about their good customer service.
The jointer came a week ago and the tablesaw came on Friday.
I will provide some coverage of my receipt and initial inspection of the G0651 Tablesaw.
Delivery: UPS freight delivery was without incident and the drivers helped me move the crates to my garage. There was minimal damage to the crates.
Uncrating: Well packaged. Pallet was intact. Initial impression is one of high quality. Fit and finish is good, decals are properly aligned. Outstanding paintwork.
Arbor Runout: Much less than .001" (more like a tenth of a thousandth).
Table Flatness: The table dips .015" in the middle, all around the blade cutout. This was measured with a new 4 foot Starrett straight edge and feeler gauges.
Extension Table Flatness: One end dips .006".
Fence Tube: Arrived with rust on the polished slide surfaces. And the attachment bolts are too short.
Fence: Looks good. Flat and straight.
Operation: I put on a plug and plugged it into 240VAC. It ran smoothly. I did not cut anything because I have the table off. The cast iron handwheels and locking knobs work well and feel good.
Today I notified Grizzly of my findings. They tell me the spec on table flatness is .015" to .020".
I think this saw has potential and I will work with Grizzly to resolve these quality issues with my saw.
Pictures follow.
5 Attachment(s)
G0651 Update and more pictures
Grizzly technical support tells me the spec for table flatness is .015" to .020". So I think I'm out of luck getting a replacement table for my saw. The encouraging news is the table flatness is better with the bolts loose. So maybe I can shim it in to an acceptable flatness. And Grizzly offered to replace rusted the fence tube but it is a 4 to 6 week lead time item and I would have to apply the rulers myself, so I told them I would assemble the saw with the rusted fence tube. The rust spot is not as bad as the picture makes it seem.
Here's more pictures of the saw.
Wait...it's missing something!
Revised table flatness spec from Grizzly
I just spoke to Grizzly tech support and was told the spec for table flatness is .001" to .002". So I think I got a bad table. Here's an update on what I found. When I removed the three bolts that hold the cast iron table to the cabinet I found no shims, but there was a .015" gap between the cast iron and the cabinet bolting flange. That means the table was pulled down and warped. I have shimmed it but the dip will not go away. I'll call Grizzly later to discuss my options.
Follow up conversation with Grizzly
Right after the Grizzly tech rep told me the spec for table flatness is .001" to .002" I got a call from another tech rep at Grizzly regarding my inquiry about table flatness. He told me the spec is .015" to .020". That means the spec is .0175" ± .0025". So mine is out of spec. I told him mine came in with a .015" dip in the table. He told me it does not matter for woodworking machines. I'll contact them again on Monday and request a replacement table since mine came in at .015". That's out of spec. I'm not pleased with having a table that should have been rejected at the factory.
Replacement table on the way
Good news. I got a call today from the Technical Manager at Grizzly. Due to the type of the defect, my table will be replaced. The new saw will be making sawdust soon.