-
6 Attachment(s)
Rehab of a saw
Had a saw come home with me..
.Attachment 362420
Missing a back, well beat up...had a backsaw that needed a new handle
Attachment 362421
They may look like bolts, but they are rivets. Handle was loose..
Attachment 362422
Maybe? Had to cut the "old" handle off, and cut the rivets. A hole or two needed adjusted, rivets were skinnier, too...
Attachment 362423
Might be a little bit better, now?
Attachment 362424
There was one nice thing about the replacement handle..
Attachment 362425
It at least had a medallion. Working on a refinish for the wood, waiting on a couple holes to get fixed....someone had drilled for a loop to hang the saw from.
One done....have a few more to do...
-
i think i might have been tempted to transplant the back onto the new (older) plate, leaving the handle where it was. I don't know the condition of that plate, though.
-
Plate was beyond hope.....
-
File the tooth line off and re-tooth. I've done it successfully. I always enjoy doing it because I feel like I accomplished something.
I have re-toothed two saws. You can draw tooth templates with a cad program or get one on line.
If you need one, send me an email and I will will send it to you.
I did that to a Disston D-8 that is now a good saw. Otherwise, clean the handle up and save for another project.
-
The plate was beyond a file job, even. Had more "kinks" that a copy of Hustler Magazine. Sharp little bends each way. Toe end was missing a chunk. Wasn't worth the effort to fix the plate. Let alone find a back for it.
IF someone else want to try to fix it up, let me know. By the time you'd add a back, and re-tooth it..there would only be 2" under the spine.
-
2 Attachment(s)
Another "saw" was cleaned up tonight...
Attachment 362511
Some of the pointy end is missing, and the teeth need sharpened.
Attachment 362512
Found the remains of a logo...." Woodrough & McParlin"? Ring a bell?
-
2 Attachment(s)
Once my bench top is clear again....
Attachment 362579
I have these two to rehab. There is a nib involved here, afterall....maybe a No.7. I think I can find enough parts to replace a few missing ones...
Attachment 362580
There are two Butcher's saws on the bottom. Most of this stack will be just for parts. Bolts and some of the handles. Most of the plates are too well bent to save.....we'll see.
-
Ok, have torn all but the riveted handled ones, and the Butcher saw down. Saved the good handles, tossed the bent plates. A Stanley "Shark Tooth" tool box saw is on the bottom. Left it alone.
Bolts have been removed, and are soaking in a bowl of full strength Simple Green. Have two straight saw plates, one a ship's saw, the other that BIG plate with a nib. I think I found the right handles for both. Rest of the handle will go to "Spares" or auction. One of the medallions is an Atkins, AAA, sunken. Will see what the rest of the medallions turn out to be. Stay tuned...
-
8 Attachment(s)
Ok, gave the parts a good soak..
Attachment 362623
And let the Simple Green work for a while
Drain it off..
Attachment 362624
Hmmm...there was 6 medallions in there..
Attachment 362625
BIG one is a Disston, there is an Atkins and most of the rest are WS.
One plate, one handle
Attachment 362626
Choosen because the holes were close.....NOT.
Attachment 362627
Last I looked, this was from a D-16? Not a..
Attachment 362628
Keystone Pacemaker....dug through the pile of handles until I found one close
Attachment 362629
WAS a 7 ppi...had been resharpened as an 8ppi ( two stamps)
Ok, brought the "other" good saw down the steps...
By the time I had found the "proper" handle and the proper bolts, and cleaned the plate up...
Attachment 362630
This is a 7ppi
Out of picture space...stay tuned, it gets even better...
-
2 Attachment(s)
There was two etches on the plate. One about being the Property of a Railway
Attachment 362631
They other is from Disston, say this is a No 7
Down on the end..
Attachment 362632
is the Nib.
So, now I have those two good saws rehabbed from the Shindig. A Keystone Pacemaker that has been sharpened a few times, and a Disston No.7 that belonged to a railway company.
I think it is time to call it a day.
-
Research says the RR was the Woodrough & McParlin RW Co. from up Vermont way.......about 1890s saw?
Found out I have two of those handles for a Disston D-16...one with carving, and one without.....Have a medallione for both of them. Have a few handles without plates, pictures after awhile.....some are HUGE 5 bolt ones ( D-23?) and one is a rather tiny, three bolt handle..I can only get three fingers in the grip..barely. May do a layout and see if anyone knows what handles they are...maybe after Lunch?
Not too hateful of a haul.....:rolleyes:
-
7 Attachment(s)
Ok, seems I had deleted one of the pictures, but here we go, anyway..
Attachment 362687
In fact, I have another just like the top one....
Attachment 362688
Not too sure about these two ( more on the wee one in a bit)
Attachment 362689
The "Bigs" and..
Attachment 362690 The Ugly
As for the wee handle.
Attachment 362691
I can only get three finger in the grip, barely
Attachment 362692
Hmmm, Brass, or steel bolts?
Attachment 362693
There wasn't any spot for a medallion.
What plates are left? All are bent, cracked and pitted....not much worth trying to "save"
These "extras" may need to go to a "Good Home"...someday.
-
4 Attachment(s)
Ok, dug through the "collection of saw plates.....found the one that fit the tiny handle.....toe had a bad bend I didn't feel like fixing, was also missing a chunk right at the toe....simple matter, I cut just behind the bad spot, and reground a profile on the end.
Attachment 362710
This pictures were taken without the tripod....if you want some tripod work..ask.
Attachment 362711
Right about here, there is a faint etch, something about "Cast Steel" and Warranted....
Attachment 362712
I chose the steel bolts, because they seemed to fit better..
Attachment 362713
I was able to "clock" the bolts, though..
Attachment 362712
Tooth line is 16" long, saw is a 10 ppi. Will need to be sharpened.
Will send this out to the fellow I know, and at $14......I will have a nicely sharpened saw.
Still trying the read the etch a little better, may have to "Gun Blue" it to bring it out better.
Had a small chip missing from the top horn, sander to blend things in. Oil finish.
Not too hateful?
-
Tooth count stamp looks a lot like a Disston one. Will wait and see what the etch says, when I can bring it out.
-
Ok, Gun Blue Paste has been used on the etch...twice. In-between the Cast Steel and a Warranted there looks to be a bearded figure, or a coat of arms...Any clues out there?
Will be taking this little saw to the local Sharpening guy.....$0.60 / inch. Min. $14 .
While re-arranging a couple saws in the till....came upon a Craftsman Special Saw.....says so right in the etch. Skew back, 8ppi. Might be a "keeper" ?