Search:

Type: Posts; User: James Baker SD; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    4
    Views
    1,076

    I used a similar product called PC ROT. It was...

    I used a similar product called PC ROT. It was both available as a putty for filling large gaps and a liquid for soaking into rotted wood. Both were 2 part epoxies. Was available at Dixieline...
  2. Replies
    40
    Views
    9,274

    I agree, shifting gears with left hand was the...

    I agree, shifting gears with left hand was the hardest part. At least the clutch was still a left foot pedal, gas/brake on right foot. Had a rental car in Scotland and all cars were manual...
  3. Replies
    11
    Views
    2,335

    Hi Wakahisa, this link is to a pretty old thread...

    Hi Wakahisa,
    this link is to a pretty old thread of mine. It has photos of my DC setup. You can see how I angled up from the DC input to the ceiling using a pair of long radius 30 degree elbows
    ...
  4. Replies
    11
    Views
    2,335

    I connected Nordfab quikfit directly to an Oneida...

    I connected Nordfab quikfit directly to an Oneida Pro500 (or whatever the 5hp pro version was called). One piece of the Onedia was a flat rectangular to 8 inch round input port that was to be bolted...
  5. Replies
    63
    Views
    9,781

    Do rotatory chambers count? They explode...

    Do rotatory chambers count? They explode gasoline and air. If they count, then 11 (4,4 & 3).
  6. I built mainly airplanes, rockets and warships. ...

    I built mainly airplanes, rockets and warships. Very first 1 was an airplane when I was 5. Nobody told me I had puncture the tube of glue with a pin so I just squeezed harder and harder until the...
  7. me too, placed order 10 minutes after I read this.

    me too, placed order 10 minutes after I read this.
  8. For those criticizing plastic handled planes,...

    For those criticizing plastic handled planes, remember when this thing was first hitting the tool store shelves, that bright colored plastic for the common man was a novel idea just as Buck Rogers...
  9. Replies
    38
    Views
    5,162

    I was going to suggest a complete shooting board...

    I was going to suggest a complete shooting board to go with the shooting plane I bought a few years back. A too long string of bad health issues has not only kept me out of my shop, but also off the...
  10. I have the equivalent machine in 16" from Felder....

    I have the equivalent machine in 16" from Felder. Don't have a problem converting between jointer and planer modes as tables move easily. Recent health problems have caused me to lose weight (no it...
  11. Replies
    24
    Views
    2,908

    what happened to the drill press shown in the...

    what happened to the drill press shown in the earliest sketch? I was going to suggest not putting it in a corner as you might need to drill a hole in the middle of a long board. I have my drill...
  12. Replies
    14
    Views
    2,906

    absolutely true, Rod. Shop is also much cleaner...

    absolutely true, Rod. Shop is also much cleaner than living room or kitchen as well
  13. Replies
    25
    Views
    4,003

    a nice thing about the Lee Valley set is if you...

    a nice thing about the Lee Valley set is if you accidentally ruin one, you can replace just that one and restore your set. They are the best brad points I have ever used.
  14. Replies
    12
    Views
    2,064

    I would think that variable density/hardness in a...

    I would think that variable density/hardness in a piece of wood, as the grain is drilled through, would push/pull on the chuck same as your hand did and thus I would guess that your hole accuracy...
  15. Replies
    7
    Views
    1,608

    I'm no MacGyver, but this is what I did with the...

    I'm no MacGyver, but this is what I did with the Performax 44/22 machine I have. I started by buying a replacement hood in case I totally screwed up. I do not see a lot of escaping dust.
    ...
  16. I have the Festool shown in the link. It is a...

    I have the Festool shown in the link. It is a linear motion. I like it a lot, but could not use it (or any sander) without the dust collector attached to it.
  17. Replies
    8
    Views
    1,201

    I kept a 6" inch thick disk from a dead Monterrey...

    I kept a 6" inch thick disk from a dead Monterrey pine, about 3' in diameter. I coated both sides with a very fluid epoxy intended to repair, or at least slow down, rot in wood structures, figuring...
  18. Replies
    2
    Views
    653

    When to harvest dead Redwood

    I have (had) a coastal redwood tree in our garden. Years of drought where too much for it and it died last Autumn. The trunk at the bottom near the soil is about 8" in diameter and the tree is 25'...
  19. I had a PM66 for several years. Used it with the...

    I had a PM66 for several years. Used it with the OEM guard and splitter with paws for a few years. Then upgraded to early version Shark, but eventually put the OEM guard back on (OEM guard was on...
  20. Replies
    50
    Views
    7,404

    I got the shot in October and the flu just after...

    I got the shot in October and the flu just after New Year's. Doctor said it should still be less bad than without the shot. I am almost over it now, hard to imagine it could be much worse.
  21. Replies
    14
    Views
    2,160

    a tank that large, especially if for marine fish...

    a tank that large, especially if for marine fish and corals, using has large filters, pumps, sumps etc, under the tank that add to the total weight and need a strong bottom shelf. I would also...
  22. I've never had a wire nut vibrate loose.

    I've never had a wire nut vibrate loose.
  23. Replies
    27
    Views
    3,395

    +1 on pizza boxes

    +1 on pizza boxes
  24. Replies
    26
    Views
    4,000

    I'm a Cincinnati fan and I can't even remember...

    I'm a Cincinnati fan and I can't even remember the last time they made it to the post season. Did have some good years back in my college days though.
  25. Replies
    15
    Views
    3,903

    I have pretty severe lung and my doctor ordered...

    I have pretty severe lung and my doctor ordered me to protect my lungs first and foremost. So an important option for me was to go with the overhead blade guard to get every last bit of dust...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4