Search:

Type: Posts; User: Tim Leo; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    13
    Views
    3,898

    I seen detailed instructions here: ...

    I seen detailed instructions here:

    http://www.hand-cut-dovetails.com/tools/8chisEgs/edges.html

    I have no affiliation with the site, just passing the link.
  2. Replies
    9
    Views
    1,555

    Maybe you could shorten the saw a couple of...

    Maybe you could shorten the saw a couple of inches to avoid the cracked area?
  3. Replies
    9
    Views
    1,437

    LIGHTLY joint the saw and try shaping the teeth...

    LIGHTLY joint the saw and try shaping the teeth again. Sometimes it takes more than one pass to get it right.
  4. A 4/4 board is 1-inch thick before it is...

    A 4/4 board is 1-inch thick before it is surfaced. The 4/4 boards I buy at the lumberyard that are surfaced on 2 sides are only 3/4-inch thick. Bringing that down to 1/2 inch thick means removing...
  5. Replies
    78
    Views
    46,544

    I enjoyed that very much. Thanks for sharing. ...

    I enjoyed that very much. Thanks for sharing. How, exactly, did you hang it on the wall? The shiplap panel on the back doesn't lend itself to screwing through the back of the cabinet to attach it...
  6. Replies
    12
    Views
    1,264

    Why is everyone cutting the cover?

    Why is everyone cutting the cover?
  7. Replies
    3
    Views
    1,015

    perfect handle repair

    Try this article:

    http://www.wkfinetools.com/contrib/jThompson/restore/perfHandle/perfHandles1.asp
  8. Replies
    3
    Views
    855

    I've got a 110 that I use all the time. Clean...

    I've got a 110 that I use all the time. Clean them up and put them to use!
  9. Thread: Ooops....

    by Tim Leo
    Replies
    27
    Views
    3,580

    I've had that problem with ebay also. Suddenly...

    I've had that problem with ebay also. Suddenly things are coming to the house that I don't need.
  10. Replies
    12
    Views
    1,891

    Maybe not. That one is for selling so you can...

    Maybe not. That one is for selling so you can buy even more user tools. If Clint is offering, I'd be selling.
  11. Replies
    17
    Views
    7,198

    I have a Norse Woodsmith saw. I think it is...

    I have a Norse Woodsmith saw. I think it is harder [to not warp or bend the saw] than you imagine.
  12. Replies
    6
    Views
    940

    Can you start the cut in the middle of the board...

    Can you start the cut in the middle of the board and work to the end?
  13. Replies
    17
    Views
    6,514

    I have the LN 60-1/2R rabbet block and I can tell...

    I have the LN 60-1/2R rabbet block and I can tell you from first hand experience that is an outstanding plane. I use it to clean up rabbits, trim tennons to size, and general block plane useage. I...
  14. Replies
    13
    Views
    1,476

    LN Handtool event? Where? When?

    LN Handtool event? Where? When?
  15. Thread: WWer Luncheon

    by Tim Leo
    Replies
    23
    Views
    2,577

    yikes, that's kinda short notice. Who showed up?

    yikes, that's kinda short notice. Who showed up?
  16. Replies
    13
    Views
    22,868

    I have set of Witherby paring chisels (with flat...

    I have set of Witherby paring chisels (with flat sides) that I use with a mallet, a set of Swan bevel edge paring chisels that are for hand use only, and a set of Stanley Defiance bench chisels for...
  17. How much of a taper will the top of the vise jaw...

    How much of a taper will the top of the vise jaw have if the vise is not tightened fully? And if you decide you dont like the taper, you can always tighten the vise, plane again, and remove the...
  18. I have a maroon (purple?) 60-1/2 that works...

    I have a maroon (purple?) 60-1/2 that works great. It did need a fair amount of fettle to get the bottom flat and get the blade to register in the advancing mechanism, but in the end it is a great...
  19. Replies
    16
    Views
    3,822

    Can you post a photo and point out the tabs?

    Can you post a photo and point out the tabs?
  20. Replies
    16
    Views
    3,822

    hard lesson?

    I think I bought the #6's brother. It looked like the surface of the moon. I spent a couple of hours with a deburring wheel and some 60 grit sandpaper to clean it up. It's not beautiful, but it...
  21. Replies
    11
    Views
    3,400

    Could you expand on that a little? How does...

    Could you expand on that a little? How does sliding the bar down change the width of the tail? I don't get it...:confused: It looks like the tapered part of the brass aligns with the wood flat...
  22. Replies
    6
    Views
    1,070

    If your not sure if they need to be replaced,...

    If your not sure if they need to be replaced, send them to me and I'll inspect them for you.
  23. Replies
    7
    Views
    1,376

    Wow. I never saw a left-handed bench before. ...

    Wow. I never saw a left-handed bench before. Cool.
  24. Replies
    9
    Views
    1,781

    You don't have to 'make' the iron. Buy a flat...

    You don't have to 'make' the iron. Buy a flat soled wooden plane from the *bay and modify it. I took a skew iron plane and cut the sole to the angle I wanted and then ground and sharpened the blade...
  25. Thread: broken 607

    by Tim Leo
    Replies
    9
    Views
    2,119

    How long did it take until the kids left the shop?

    How long did it take until the kids left the shop?
Results 1 to 25 of 105
Page 1 of 5 1 2 3 4