Search:

Type: Posts; User: Michael N Taylor; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    21
    Views
    8,166

    Tandy leather craft has all kinds of leather and...

    Tandy leather craft has all kinds of leather and you can usually find what you want, if there is not one in your area you can order online.
  2. Replies
    5
    Views
    2,755

    Fabrication and Shop Techniques I have never done it but I was looking on a site...

    I have never done it but I was looking on a site and they heated the metal to a yellow orange color then immediately drop in in a bucket of water or oil. I would definitely try it on a scrap piece of...
  3. I installed 6" blast gates on the main line to...

    I installed 6" blast gates on the main line to every branch line, this allows me to keep the lines closed to areas I am not using and being a one man shop I cannot use but one tool at a time. This...
  4. Replies
    17
    Views
    5,317

    A one inch hole should not weaken the foundation...

    A one inch hole should not weaken the foundation no matter where it is drilled. The only thing is there should be rebar within 3-4 inches of the top of the foundation, if it was me I would drill 6"...
  5. I have been involved with block buildings for 42...

    I have been involved with block buildings for 42 years and any good foam company can drill small holes in the block and fill the cavities with foam. There are two types of foam, closed cell and open...
  6. Replies
    16
    Views
    4,720

    I have had good success with T-111 you just need...

    I have had good success with T-111 you just need to prime all of the edges and back before you install it. I always do 2 coats of primer since it is rough and soaks up the first coat pretty fast.
  7. Replies
    12
    Views
    2,226

    My shop is plain concrete sealed with a silicon...

    My shop is plain concrete sealed with a silicon base sealer and it has work very well for me. The concrete lightens as it ages and the silicon sealer keeps dust down plus seals out moisture without...
  8. All you need to do to concrete is to apply 2...

    All you need to do to concrete is to apply 2 coast of a silicon base concrete sealer to keep moisture from wicking up and to stop stuff from staining. This type sealer does not make the floor slick...
  9. Replies
    24
    Views
    6,694

    I have 2 jet air filters and they work great, but...

    I have 2 jet air filters and they work great, but I do use different filters. The jet filters are expensive so I did a Google search for 2" filters, I have bought from several different suppliers an...
  10. Replies
    19
    Views
    63,346

    To me the best floor for a shop in a basement is...

    To me the best floor for a shop in a basement is sealed concrete. Clean the concrete by sweeping then mopping and let dry before applying a good penetrating sealer, this will soak into the concrete...
  11. Replies
    14
    Views
    2,011

    I am no expert but I would glue the smooth side...

    I am no expert but I would glue the smooth side and leave the rough side out.
  12. Replies
    35
    Views
    10,294

    The Suspender Factory carries a lot of different...

    The Suspender Factory carries a lot of different suspenders in several width ad materials.
  13. Replies
    25
    Views
    5,552

    You can simply set a string line from each corner...

    You can simply set a string line from each corner and cut every stud to length to get the top of the wall level but I would go after the contractor to make it right. I hope when you had the work done...
  14. Replies
    17
    Views
    4,441

    I just received an order from Zoro tools and it...

    I just received an order from Zoro tools and it was very smooth, Ithey shipped very quickly and I had the order in the 3rd working day.
  15. Replies
    20
    Views
    9,071

    I have a basement shop and I run a dehumidifier...

    I have a basement shop and I run a dehumidifier all the time to keep it at 55% humidity in the summer, that is as low as I can get it with one unit running. I would think the garage would be harder...
  16. Replies
    13
    Views
    3,131

    I taped mine but I am not sure how much it helps...

    I taped mine but I am not sure how much it helps since the snaplock is pretty tight to start with but it never hurts to go one more step.
  17. Replies
    16
    Views
    6,373

    I just got the Sigma II's in 1200, 8,000,& 13,000...

    I just got the Sigma II's in 1200, 8,000,& 13,000 and I was really surprised how fast you can sharpen with them. I also have a DMT coarse plate that I use to get the secondary and micro bevels first...
  18. Replies
    10
    Views
    1,520

    You should have no problems running the pipe on...

    You should have no problems running the pipe on the wall, I have seen someone carrying 6" metal hose hangers that can be mounted with drywall screws.
  19. I bought one of those shop cranes on sale and it...

    I bought one of those shop cranes on sale and it really comes in handy lifting and moving machines. It is a 2 ton capacity and was only $125.00 on sale from an auto parts supply store. You can hoist...
  20. Replies
    22
    Views
    3,109

    Any commercial HVAC supply house can get you 26...

    Any commercial HVAC supply house can get you 26 ga. snap duct and it works great. I used the 30 ga fittings and have not had any problems with my 2.5 hp collector. be sure and buy a couple of rolls...
  21. Replies
    22
    Views
    3,109

    I got the metal gates from Lee Valley on sale and...

    I got the metal gates from Lee Valley on sale and they have been very good.
  22. You can buy the pvc pipe at Ferguson's plumbing...

    You can buy the pvc pipe at Ferguson's plumbing and hvac, Steinhouse plumbing supply or any commercial plumbing supply house in Nashville. I bought 6" 27 ga. metal duct and 30 ga fittings from...
  23. I have been involved in metal buildings in...

    I have been involved in metal buildings in commercial construction from 1978 to 2010. The top of the line buildeing is Butler, they have the MR24 roof system that is seamed together like the seams on...
  24. Please qdd my name to this drawing. Thanks

    Please qdd my name to this drawing.
    Thanks
  25. add my name to this drawing please

    add my name to this drawing please
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4