Search:

Type: Posts; User: Frank Corker; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.40 seconds.

  1. Replies
    3
    Views
    1,204

    Give CSI a call 01179114367 they are the...

    Give CSI a call 01179114367 they are the distributors for Epilog if they don't have it I'm sure they can point you in the right direction.
    www.csionline.co.uk
  2. Replies
    3
    Views
    1,252

    I have a four inch lens but to be honest, it does...

    I have a four inch lens but to be honest, it does cut fine, but it doesn't engrave cast with the same crisp quality. As for the quality of cut on thicker materials it is supposed to be better but...
  3. Replies
    8
    Views
    2,117

    I think it's a sticky plunger too. The contact...

    I think it's a sticky plunger too. The contact is right at the top of the black rectangular part that slides upwards. If you remove the plunger and then gently tap it up and down the contact will...
  4. Replies
    20
    Views
    4,833

    The demo shown on the YouTube for gluing the...

    The demo shown on the YouTube for gluing the award to the base is scary. I would never lift the object. Movement that she had going there would have resulted in marking and wiping the cloth over...
  5. Replies
    6
    Views
    1,598

    Their prices are laughable!

    Their prices are laughable!
  6. Replies
    6
    Views
    2,088

    Your power, speed and frequency are okay to cut...

    Your power, speed and frequency are okay to cut the material. Obviously from the finish, the result is not what you want. In this case, you are using black acrylic, this for me is notorious for...
  7. A lot of them have the same issue. Mine can take...

    A lot of them have the same issue. Mine can take a minute or two before the tube is ready to fire. In the settings in the manual, there is a laser tickle that can be activated, but I never looked...
  8. Thread: UpSelling

    by Frank Corker
    Replies
    7
    Views
    2,500

    Well done Tim, good to hear a nice story every...

    Well done Tim, good to hear a nice story every now and then.
  9. Replies
    4
    Views
    1,636

    Anything black, picture wise, should be done in...

    Anything black, picture wise, should be done in negative.
  10. Replies
    5
    Views
    1,794

    That's looking very nice. Good colour too.

    That's looking very nice. Good colour too.
  11. Replies
    20
    Views
    3,763

    Steve is without doubt the right man for the job...

    Steve is without doubt the right man for the job and one of the most knowledgeable. Good choice.
  12. Replies
    10
    Views
    2,108

    I thought it was an actor

    I thought it was an actor
  13. Replies
    29
    Views
    5,842

    From Dan: I'd appreciate it if you would...

    From Dan:

    I'd appreciate it if you would pass along I'm closing on a home next month, preparing for being out of the country for a few weeks, and trying to finish remodelling my current home...
  14. Replies
    29
    Views
    5,842

    He's on Facebook I'll let him know you were asking

    He's on Facebook I'll let him know you were asking
  15. Replies
    4
    Views
    1,493

    I agree with Mike. Laser beam alignment, go to...

    I agree with Mike. Laser beam alignment, go to the Epilog website and view the tutorial or check from the manual. That metal tray is not generally used for cutting on, you should use your vector...
  16. Graham, I have never had any issues with the...

    Graham, I have never had any issues with the venting problems, most of the time the smells are so minimal you can hardly detect them anyway. I work from home and none of my neighbours have had any...
  17. Replies
    13
    Views
    2,388

    That looks a little like acrylic sweat marks,...

    That looks a little like acrylic sweat marks, where the vapour from the cut acrylic sticks to the shiny surface. Transfer tape might help prevent it. It might also be from having alcohol on it...
  18. Replies
    16
    Views
    3,446

    If you need help with these, you need to present...

    If you need help with these, you need to present better quality pictures definitely bigger than those you have put up here. Someone will most likely help, might I suggest you put the full size scans...
  19. Stan they look nice but you seem to have a lot of...

    Stan they look nice but you seem to have a lot of banding in them.
  20. Replies
    15
    Views
    2,371

    Joe's analysis is spot on. Transfer tape will...

    Joe's analysis is spot on. Transfer tape will stop the hazing too.
  21. Replies
    3
    Views
    1,173

    From the Helix manual which can be downloaded...

    From the Helix manual which can be downloaded from Epilog website.
    All Epilog model 8000 laser systems require an exhaust fan that is rated
    at a minimum of 400 CFM at 6” of static pressure 680 M3...
  22. Replies
    1
    Views
    894

    Josh a lot will depend on what you are using it...

    Josh a lot will depend on what you are using it for. Anything that smokes heavily, a lower cfm might not be able to exhaust the fumes out fast enough. On some materials, it can be hazardous and...
  23. Replies
    22
    Views
    4,545

    The 4" lens cuts okay, not a fantastic bit of...

    The 4" lens cuts okay, not a fantastic bit of difference. The engraving on acrylic is definitely not as good as with the standard lens, less frosty, on wood it is fine, I have to be honest and say I...
  24. Replies
    5
    Views
    1,068

    I think that the best rule of sum is the higher...

    I think that the best rule of sum is the higher the dpi and resolution of the image the better, however there are occasions when too high dpi will result on too much damage to the image. Wood will...
  25. Yup, that is impressive, but I can only see it...

    Yup, that is impressive, but I can only see it being used for the purpose that was on the video. Looks pretty scary actually.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4