PVC can cause static electrcity and that's a fact, but MIT did a study on the use of pvc on systems uner 3hp and found out that there is pretty much no chance of an explosion.
But my question to...
Type: Posts; User: Jimmy Coull; Keyword(s):
PVC can cause static electrcity and that's a fact, but MIT did a study on the use of pvc on systems uner 3hp and found out that there is pretty much no chance of an explosion.
But my question to...
David,
I respectfully disagree with 20 amp rating on the HF motor as stated. You can call it 14 amps or 20 amps but it tests as closer to 14 amps. It can be wired for 110v, if it wre 20 amps it...
Angie,
It looks great, let us know how it works out down the road, or if it's gonna need a son of a son of a .........:D
Thanks,
Jimmy
I would not go with 6" for one main reason and that's the DC size. The HF DC is a very good "bang for the buck" tool, but HF fluffs there motor hp. and the HF 2hp is really a 1-1/2 hp this has been...
Warranty not guarantee, that says it all. First of all, when something goes wrong with the Ikea cabinet, and it will because of either soft woods or being particle board, they will replace, or credit...
I also recommend the L-N #9 miter plane, which is designed after the Stanley #9 which is very hard to find. I used one during a dovetail class, I was taking from Bill Anderson in Chapel Hill, NC,...
Glenn,
I don't think that it would work only because the air used for the draw(from a blower) has a capability of being compressed. When I worked in the power industry we used sluicing water, that...
Rick,
Concrete will be the least expensive floor, if you have more money install a wooden floor over it using 2 x 4's layed down flat with plywood over it and the Radiant floor heating can be run...
Scott,
A few thins that I left out :
1) I used screws to hold the half lap joints together and....
2) When putting nails and screws in to the door during construction, make sure that...
Russ if you are going to make a raised floor you should think about running tubes with it for radiant heat, the heater itself would just be a hot water heater and a pump. It would keep you...
I've made these type of doors for a shop before, I had to make two 48" x 96" doors. Make the frame out of 2 x 4's , it will be a 42" X 96" rectangle with 2 x 4 across the middle creating two 42" x...
I personally think it makes sense if you can get a good used deal on a 15" planer, my PM (an older model M-15 was $400)was cheap enough, and if I ever find a really good deal on a 735 I'd mount it on...
Jim,
The only advise that I can give you is to start something in one corner and go from there. Your shop sounds alot like mine did two years ago and I still haven't gotten as much done as I...
Try to use the non obvious spaces, such as unter the TS wings, Put the RAS on a cabinet, sit your BS on a cabinet instead of a stand, same with you planer, etc., and put all machines on mobile bases....
I have a 3 hp pm and agree that they run quieter and have more power....But what are you looking to do ? If you buy your wood rough and need to clean it up, by all means purchase the Jet, the DeWalt...
I second the router bit, if you don't use the Rockler bit you can use core box bits with a plunge router.
Good Luck,
Jimmy
Thanks All !
I was hoping to hear that.
Jimmy
Does anybody have an idea on whether a blower that's made to run vertically can be turned sideways (horizontal) without any problems. Changing it might make a difference to some of the bearings, but...
Thanks Tom,
I'll check out the amps when I get it up and running. :>)
I am planning on running a Wood magazine type cyclone as a dust seperator connected to a Grizzly 2hp. blower w/a 12" impeller (from a 1029z DC) through all 6" lines which will then blow the fines...
It's funny you mention the cabinets falling, because that happened to a friend of mine years ago but it was caused by using sheetrock screws, after that happened I read that sheet rock screws were...
Wes,
You don't have to make it, you just need to know where to find it. Here's a website :
http://www.rvupgradestore.com/browseproducts/30-Amp-RV-Extension-Cord--25'.HTML
Good Luck,
Jimmy
I ran a 60 amp service to an old detached shop that I had and used 6/3 w/g wire and had absolutely no problem. My wire was free and someone gave me the subpanel and that is why I did it that way. I...
Heat tracing uses an electrical heating wire that you attach to the length of your pipe that might freeze up. it can work off a thermostat or you can turn it on and off by yourself.
Putting the filter back into the room will prevent a negative air problem, it will also bring conditioned air (a/c or heat) back in to the room without much loss.
Good luck,
Jimmy