Search:

Type: Posts; User: Tony De Masi; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    16
    Views
    2,904

    Roger, beautiful form on this piece and the wood...

    Roger, beautiful form on this piece and the wood speaks for itself, as it should. Glad to see that you didn't do any fill work especially in that larger void. And of course congrats on the sale. ...
  2. Replies
    23
    Views
    4,422

    Personally I would proceed as normal and just...

    Personally I would proceed as normal and just fill enough of those holes in the bottom to assist with vacuum chucking during finish turning, IF they indeed turn out to be through and through holes.
  3. Replies
    8
    Views
    1,957

    Decent enough of a save. But if you are leaving a...

    Decent enough of a save. But if you are leaving a nub, center bottom, while hollowing then whatever bit you are using in that area is not dead nuts center.
  4. Replies
    49
    Views
    8,177

    Well I would start with what you are calling "the...

    Well I would start with what you are calling "the same dumb mistakes". As you look at this piece what are you seeing as a repeat mistake? There is nothing wrong with the shape as long as this is...
  5. I run two old upright freezers for drying rough...

    I run two old upright freezers for drying rough outs. Incandescent 150w bulb plus fan. I use this dimmer switch, link below, which allows me to change the output of the bulb without opening the...
  6. Replies
    20
    Views
    5,010

    In the warmer weather, when I wear shorts when I...

    In the warmer weather, when I wear shorts when I turn, I use these:

    http://thesandingglove.com/DUST-BEE-GONE-Shoe-Covers.asp
  7. Replies
    17
    Views
    2,558

    Ken, your friend and my friend have much in...

    Ken, your friend and my friend have much in common. Yesterday mine told me that he CA glued his wedding ring to his finger. I told him to go get some nail polish remover from his wife and that...
  8. I remove the bit's from the shaft and simply hold...

    I remove the bit's from the shaft and simply hold them flat down on the platform on my vari grind jig. Set the angle, one rotation, and done. No jig needed.
  9. Replies
    12
    Views
    2,592

    I saturate my "user" bowls as you do. Usually...

    I saturate my "user" bowls as you do. Usually two coats 24 hours apart. I go through a lot of walnut oil and used to get the Mahoneys. But his product had gotten too dark in color for me. I mine...
  10. Replies
    12
    Views
    2,591

    You will love the new grinder, and wheels of...

    You will love the new grinder, and wheels of course. But you may as well just pull the bulb out of that light as it pretty useless.
  11. Replies
    12
    Views
    2,213

    Mark is a great teacher but a better person. ...

    Mark is a great teacher but a better person. Looks like nice visit.
  12. Replies
    9
    Views
    2,115

    Nicely done Steve. That should be a fairly easy...

    Nicely done Steve. That should be a fairly easy sell.
  13. Replies
    16
    Views
    4,006

    Recently, past two years, I've used both the...

    Recently, past two years, I've used both the Timberwolf AS blades and the Lennox Die Master II blades. Both 1/2", 3 tpi. I too use them for thick, green blanks. For me they both cut fine but the...
  14. Replies
    13
    Views
    2,255

    Little late to see this but never too late to...

    Little late to see this but never too late to pray for you both.
  15. Replies
    17
    Views
    3,943

    Try saving a copy of each pic before you...

    Try saving a copy of each pic before you manipulate for thst very reason.
  16. Replies
    17
    Views
    3,943

    Nicely done Roger. The curve looks spot on...

    Nicely done Roger. The curve looks spot on though I really hesitate to say that without actually holding the piece in my own hands. Not sure what you are using to manipulate your photos but with...
  17. Replies
    11
    Views
    2,211

    Roger, I pretty much buff all of my turnings, the...

    Roger, I pretty much buff all of my turnings, the ones that aren't straight utilitarian anyway. I start with the tripoli then move to white diamond. I don't use the carnuba at all. I run the lathe...
  18. Replies
    7
    Views
    1,492

    John, yes you need to do a bit more research. ...

    John, yes you need to do a bit more research. What you are describing is a commerce site. One in which you can sell your wares. I don't know of ANY commerce sites that are free. Not saying that...
  19. Replies
    12
    Views
    1,792

    That's awesome news Brian. Continued good...

    That's awesome news Brian. Continued good thoughts to your daughter and the rest of your family.
  20. Replies
    27
    Views
    4,442

    Mark, these are what I wear. ...

    Mark, these are what I wear.

    http://www.merrell.com/US/en/jungle-moc/17703M.html?dwvar_17703M_color=J71443#cgid=men-featured-best-sellers&start=1
  21. Replies
    27
    Views
    4,442

    +1 on the Merrell Jungle Moc's. I've been...

    +1 on the Merrell Jungle Moc's. I've been wearing the same pair pretty much every day for the last two years. I'm in my shop every day doing something, mostly turning, and I love these things. ...
  22. Replies
    4
    Views
    1,060

    Mine were mounted on steel poles after being...

    Mine were mounted on steel poles after being taken down from the roof. Both the TV and Internet dishes were moved and mounted at no charge by the company.
  23. I can probably guess Roger. And I'm feeling well...

    I can probably guess Roger. And I'm feeling well enough now that I can probably help load you up too.
  24. Well Roger you certainly took a very different...

    Well Roger you certainly took a very different road than I would have. Mine would have been sent back for a new set that would hopefully be better spec'd.

    If you need more cherry burl you know...
  25. Replies
    23
    Views
    6,591

    Post length is 5 and 7/8 ths.

    Post length is 5 and 7/8 ths.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4