Search:

Type: Posts; User: Jim Podsedly; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    33
    Views
    6,370

    Hey Pete. I haven't been on this forum in a...

    Hey Pete. I haven't been on this forum in a while but saw this thread while perusing. Who moved? That is a sweet lathe! Who got your mustard? How are things in MI? Not doing too much turning...
  2. Replies
    15
    Views
    3,574

    Boot up in safe mode and run malwarebytes. ...

    Boot up in safe mode and run malwarebytes. should remove any malware on your system.
  3. Replies
    7
    Views
    2,112

    The Palmgren was my first lathe. I had issues...

    The Palmgren was my first lathe. I had issues with the headstock so they sent me another one. Well, it was frustrating using the lathe so i upgraded. See the picture of what my two headstocks...
  4. Replies
    14
    Views
    3,154

    I have had great success using O.B.'s shine...

    I have had great success using O.B.'s shine juice.
    This is part of an article explaining the shine juice:



    O.B.’s Shine Juice
    By Capt. Eddie Castelin
  5. Replies
    9
    Views
    1,424

    Pete, Again very very nice platters and bowl. ...

    Pete, Again very very nice platters and bowl. Is your garage filled with shavings after turning those big pieces?!!!

    jim
  6. Replies
    20
    Views
    3,467

    Pete, Some great looking platters. Love the...

    Pete, Some great looking platters. Love the grain and finish.

    BTW - did you get that box of shells?

    jim
  7. Replies
    5
    Views
    871

    Satellite Beach, FL ?

    We have been to Florida many times and have our mind set on relocating there. We have been looking all over the east coast and have found a very nice potential house in the Satellite Beach area.
    ...
  8. Replies
    18
    Views
    2,110

    nice haul.. i will be over in a couple weeks! ...

    nice haul.. i will be over in a couple weeks! that should be enough wood for the ornaments.
  9. Replies
    17
    Views
    2,205

    Nice score!

    Nice score!
  10. Replies
    15
    Views
    2,469

    I have been using the fans for a few days, then...

    I have been using the fans for a few days, then 80, then 90 then 100 for each a week. the RH dropped to ~20% at the end.

    Also, the type of wood you have in the kiln really makes a difference. I...
  11. Replies
    13
    Views
    1,936

    I missed a good night. I need to run down to...

    I missed a good night. I need to run down to your house and try one of those! Great idea!
  12. Replies
    10
    Views
    3,540

    I am leaning toward this one at Lowes: Utilitech ...

    I am leaning toward this one at Lowes: Utilitech 18" 3-Light Linking LED Bar

    I am still trying to find out if this can be hardwired. It says it has a plug so I am guessing i could wire...
  13. Replies
    10
    Views
    3,540

    Under Cabinet Lighting suggestions

    Looking to remove our outdated fluorescent fixtures and replace with something more modern.

    The lights are hardwired to switches currently and would like to keep that method of operation.

    I...
  14. Replies
    4
    Views
    2,736

    We have a retractable screen on our front door. ...

    We have a retractable screen on our front door. It needed to be reset/rewound when our dog ran or tried to run through it once. Other than that it has been nice to have a screen at times and not at...
  15. Replies
    23
    Views
    2,493

    That is a great looking bowl. After...

    That is a great looking bowl.
    After creating/finishing my first segmented bowl recently, i have a brand new appreciation for all the great segmented bowl turners on this forum.
  16. Replies
    12
    Views
    1,961

    the segmented turning is very time consuming. i...

    the segmented turning is very time consuming. i am more for immediate gratification -- taking a log and making a bowl all within a hour or so.
  17. Replies
    12
    Views
    1,961

    First segmented bowl

    Here are two firsts.

    Segmented bowl - made from walnut and maple. Measurements 9"Wx5"h

    Off center turning - The spatula was fun to make.

    Not sure if i will be making these again but...
  18. Replies
    29
    Views
    3,004

    A free tool that i use quite a bit is CCleaner. ...

    A free tool that i use quite a bit is CCleaner. It will clean up lots of uneeded files thus freeing up disk space. It also has a registry cleaner. Regularly cleaning the regisitry is a good way to...
  19. Replies
    12
    Views
    1,266

    Dan, i am using a gast 220 pump and a 20A...

    Dan,

    i am using a gast 220 pump and a 20A Double Pole Switch is all i needed.

    jim
  20. Replies
    29
    Views
    2,338

    I would blow out all the holes on the laptop to...

    I would blow out all the holes on the laptop to start with. You would be surprised how much dust gets in there and how much harder/hotter it makes your pc work.

    Secondly run malwarebytes. this...
  21. Replies
    22
    Views
    3,145

    Bill, Very nice bowls. When creating the...

    Bill,

    Very nice bowls.

    When creating the segments, are they the side grain of the wood or top?

    Soon will be venturing into the segment vortex! :-)

    jim
  22. Replies
    10
    Views
    1,647

    Do most use a stem with the crush grind mechanism...

    Do most use a stem with the crush grind mechanism or the stemless ones.

    I guess one advantage to the stemless is that you are not limiting the size of the mill and you do not have a knob...
  23. Replies
    25
    Views
    6,287

    I also use the same drill as Bernie from Harbor...

    I also use the same drill as Bernie from Harbor Freight.

    I have had good results with sanding discs from Vince. The key is to not let the discs get too hot:
    ...
  24. Replies
    17
    Views
    2,171

    That is one sweet saw! congrats!

    That is one sweet saw! congrats!
  25. Thread: Kiln

    by Jim Podsedly
    Replies
    5
    Views
    1,424

    Kiln

    This has been something I wanted to build for some time now. With all the kilns being built by the members here lit a fire under me! :-)

    I followed these instructions to build the kiln. ...
Results 1 to 25 of 225
Page 1 of 9 1 2 3 4