Search:

Type: Posts; User: Alan Zenreich; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    32
    Views
    8,607

    Dwight, The video I posted using a CCTV...

    Dwight,

    The video I posted using a CCTV camera is an effective implementation of a simple camera setup.
    It is one of three hollowing variations I show in a youtube clip I made about several...
  2. Replies
    5
    Views
    1,875

    I tend to make smaller items, for example,...

    I tend to make smaller items, for example, jewelry and shaving brushes.
    I really like using a "Mark St. Ledger" 5/8" spindle roughing gouge from Thompson Lathe Tools (it is listed under 'other'...
  3. Replies
    4
    Views
    1,449

    Lauren and I spent time with Bill a few years...

    Lauren and I spent time with Bill a few years ago... Time very well spent.
  4. Replies
    20
    Views
    8,264

    I respectfully disagree with Steve about the...

    I respectfully disagree with Steve about the Allen head screws. I find no problem at all with the thumb screws, finger tight is fine for my turning. Considering how often I reposition the index...
  5. Replies
    20
    Views
    8,264

    Dave, Lauren and I appreciate your kind words...

    Dave,

    Lauren and I appreciate your kind words about our presentation in Tampa.

    If you have any questions, or just want to chat a bit, send me a private message, and we can talk on the phone.
  6. Replies
    9
    Views
    2,927

    Same for...

    Same for
    http://www.sawmillcreek.org/showthread.php?206951-Joyner-pendant-jig-problem
  7. Replies
    20
    Views
    8,264

    For my use, I find turners tape much much better...

    For my use, I find turners tape much much better than any of the carpet tapes I have tried. The key is light cuts. Keep visualizing that your work is only being held on by tape, so go gently, and...
  8. Replies
    14
    Views
    2,738

    Lovely. Very nicely done.

    Lovely. Very nicely done.
  9. Replies
    18
    Views
    4,702

    Mike, don't forget to use the tilt adjust to...

    Mike, don't forget to use the tilt adjust to "balance" the unit on your head so that it's neither pulling forwards nor backwards. It makes a big difference in comfort.
  10. Replies
    18
    Views
    4,702

    Rich, You mentioned "The 3M Airstream takes...

    Rich,


    You mentioned "The 3M Airstream takes care of both particulate and fumes"

    The 3M AirStream with the blower in the helmet is particulate only, using an in-helmet HEPA filter.

    The 3M...
  11. Replies
    17
    Views
    2,812

    John, some demonstrators are "invited", and then...

    John, some demonstrators are "invited", and then there is a general call for topics, where anyone can submit their demonstration proposals. So keep your eyes open for the call for topics deadlines....
  12. Replies
    17
    Views
    2,812

    It was great seeing familiar faces, as well as...

    It was great seeing familiar faces, as well as the graybeards newly met. Lauren and I had a fine time, and hope the folks who attended our demos enjoyed them as much as we did. The feedback we...
  13. Replies
    7
    Views
    1,342

    I'd just make sure that all the circuit boards...

    I'd just make sure that all the circuit boards and ribbon cables are connected securely... and then give Nova support a phone call.
  14. Replies
    7
    Views
    1,342

    First thing I'd check.... Are you pressing the...

    First thing I'd check.... Are you pressing the remote button in for 2 seconds to start the lathe? You might not be pressing the button for long enough.
  15. Jon, Absolutely, it takes only about 3 more...

    Jon,

    Absolutely, it takes only about 3 more minutes to make two instead of one... make them by the dozen <vbg>
  16. Sticky Stick: AAW FUNdamentals video

    I recently became a member of the AAW Woodturning FUNdamentals committee.

    This video accompanies a short article I wrote for the May/June newsletter.

    It's a simple enough accessory to build. I...
  17. Replies
    7
    Views
    1,441

    First you get a cello to autoplay in your shop....

    First you get a cello to autoplay in your shop....
  18. Replies
    7
    Views
    1,401

    .... and don't inadvertantly throw away the...

    .... and don't inadvertantly throw away the little board... the packaging makes it easy to miss.
  19. Replies
    7
    Views
    1,401

    Eric, come on in, the water's fine

    Eric, come on in, the water's fine <vbg>
  20. Replies
    19
    Views
    2,910

    Thanks one and all for the kind words. We really...

    Thanks one and all for the kind words. We really are having a good time making these pendants, and sharing the techniques and toys, cough, errrr.... tools used to produce them.
  21. Replies
    19
    Views
    2,910

    Thanks Brian, sorry we didn't get a chance to...

    Thanks Brian, sorry we didn't get a chance to meet... come visit in NJ!
  22. Replies
    19
    Views
    2,910

    Bill, we're having great fun experimenting with...

    Bill, we're having great fun experimenting with many tools and techniques... brass inlay, polymer clay, precious metal clay, dyes, inlace, wood inlaying, semi precious stones, airbrushing, piercing,...
  23. Replies
    19
    Views
    2,910

    Harry, yes, we're using archival in pens and...

    Harry, yes, we're using archival in pens and brushes from Pigma... mostly in .005 and .05 point sizes.
  24. Replies
    19
    Views
    2,910

    Charlie, I turned a very thin, tapered, flat...

    Charlie, I turned a very thin, tapered, flat bottomed "cup" that encloses the back... it's just wide enough to cover the wirework.

    This is just something Lauren is playing with... we have some...
  25. Replies
    19
    Views
    2,910

    David, This was a turning project, all done...

    David,

    This was a turning project, all done on the lathe, no carving. Here are a couple of photos that might give some insight into how it was made.

    The wood is a laminate flooring product...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4