<p>
I believe Panhans is a subsidiary of the company that bought Aggazani out. http://www.hokubema.de/agazzani.html Translating the page: The well-known band saw manufacturer AGAZZANI was taken...
Type: Posts; User: Larry Gipson; Keyword(s):
<p>
I believe Panhans is a subsidiary of the company that bought Aggazani out. http://www.hokubema.de/agazzani.html Translating the page: The well-known band saw manufacturer AGAZZANI was taken...
2. The saw table has a miter slot, but it is less than 1/8" deep. Is this really for a miter gage? Sure seems strange. Do they make a miter gage for this saw? In any case I just want to make a sled...
I have the NRA 500 and I really like everything except for the shallow crosscut miter slot. I've misplaced the crosscut miter that came with the saw since the move, but it really didn't work all that...
Not sure about a heavy bench, but I've used leveling feet from a company in Signal Hill (Long Beach) Ca.
http://www.levelingmounts.com/ I have them on my table saw and on a bandsaw. The one's I...
Can you move the table by pulling the chain? If you can move the motor shaft easily with no chain, but the chain won't budge by hand, then it sounds like one or more of the threaded rods or the...
This is a fascinating discussion for me since I'm finishing my first cutting board at the moment. The board is hard maple (16x22) with a 3/4 in "border" of padauk. The entire board, including the...
Thanks! I'll try it.
- Larry
I've been searching for a couple of days on this. The vac outlet on the tool is about 7/8" or 22mm od. I was hoping to find an adapter to use my Bosch vac hose (~27mm id / ~35mm od) but no luck. ...
They're likely being held together with grease or oil. The only other explanation would be
rust. I'd soak them in solvent or blade cleaner for awhile, then try to slide them to break any bond. ...
I understand the Bosch jig saws have a zero clearance insert similar to my Festool. Is this so? If so, how hard is it to buy replacements? Does the insert adequately reduce top tear out? A friend...
I have a larger version of that generator and have had nothing but problems with it. The engine has never run smoothly and somehow "hunts" then stalls. There's a feedback system that adjusts the...
I got one also. Not at the sale price though. Oh well.
David, pm me and I'll send you a larger picture if you like. The one I posted can be zoomed in on (right click; open in new tab; ctrl + )
This is just a large hinge made from 1/4" plate steel I...
Bill, that's pretty close to what I thought I might do when it was too late to do it :) I had the hinge made. I thought about installing 2 L brackets, one on each end of the top brace on the rear...
325384
I suppose a picture would help. All mods are bolt-on so the machine can easily go back to factory spec if desired.
The bottom pulley consists of these 2 pieces:
TB Woods Type QT QT34...
I should probably update this. I finished the mod on my 490x shortly after I wrote this initial inquiry.
There were 2 separate issues I've solved. First, it was too hard to adjust belt...
If you're talking about something like the Kreg pocket screw system, I don't actually trim plugs down after installation. I use their 3/8" stepped drill bit to make the holes, so use 3/8" dowel to...
I second the fly cutter. I'd first cut a 2" circle from plywood so that it will just fit the existing hole. That will locate the center. Then use the fly cutter again to cut the larger hole. I'd...
The belt isn't the issue. It's the new ribbed belt. The problem I seem to be having is getting enough tension on the belt. Also keeping the pulley tight enough. I checked it today and things have...
You will have to completely rewire the motor to safely use something wired for 110v on 220v. Most of these have 2 sets of coils. They may be in parallel for 110v and in series for 220v. Put an...
I remember the post you refer to and set the thing up that way the last time I fooled with it - thanks(!).
About a year after I set it up the first time, the little set screws worked loose on...
Hi guys,
I have a Grizzly jointer that's a couple years old. Since I bought it, I've wanted to redesign/rebuild the motor mount. The way it came, it's pretty hard to get the belt tension, motor...
Sounds about right. My dad always used a 20 or 30wt non-detergent oil on babbit bearings. He was a chief machinists mate in the Navy for 20yrs and lived inside aircraft carrier engines for several...
There was a glue thread here: http://tinyurl.com/knxatek
There is a product that will soften the titebond products http://de-gluegoo.com/
Looks nice. When I've used Rust Free on cast surfaces like my Unisaw, I've managed to leave behind sort of a splotchy surface. I'm probably a klutz. If I follow up with a medium scotchbrite pad...