Search:

Type: Posts; User: walter hofmann; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    932

    hi there I make my own I use small pieces of the...

    hi there
    I make my own I use small pieces of the acrylic then dissolve it in aceton until its totally dissolved like coffee cream.
    maybe this helps
    greetings
    waltfl
  2. Replies
    57
    Views
    11,931

    hi all here are a few picture from my workshop...

    hi all
    here are a few picture from my workshop after downsizing from 1200SF to 400SF garage .
    its all stuffed but all machines can be used . for cooling I use a 22000 BTU window AC what is also ...
  3. I got condensation on my tube all the time...

    I got condensation on my tube all the time because of the ambient temp of around 36 C and like I said my water temperature runs between 15 and 20 C. my cheap tube ( ebay $ 160) last around 1,300...
  4. 40W water between 15 and 20 C

    40W water between 15 and 20 C
  5. Replies
    17
    Views
    3,083

    I use mostly " acrylite 2.5mm" I get them for...

    I use mostly " acrylite 2.5mm" I get them for free from my local ACE hardware store they have every week quite a lot of cutoffs and I get them for free.
    ones in a while I give the girls something I...
  6. Replies
    23
    Views
    5,930

    hi guys its a matter of opinion but this was not...

    hi guys
    its a matter of opinion but this was not the question if I remember right it was regards to engraving bamboo.
    I just try to help out glen.
    the design is not in question.
    greetings
    waltfl
  7. Replies
    21
    Views
    4,541

    hi there I can not open the corel file because I...

    hi there
    I can not open the corel file because I got X5 but why don't you group all and send it to the laser that's how I do it but I got lasercad not lasercut.
    for the acrylic I get left over...
  8. Replies
    23
    Views
    5,930

    maybe this helps I am using the scrap pieces...

    maybe this helps
    I am using the scrap pieces from the flooring installer of bamboo I get them for free and the good part is that the surface is already sealed.

    they give318609318610 it for free....
  9. Replies
    3
    Views
    1,087

    I would replace the tube first because that's the...

    I would replace the tube first because that's the part what goes first seldom the powersupply and the controller has not much to do if the power goes down.
    greetings
    waltfl
  10. Replies
    9
    Views
    2,242

    ground is required for both operation and safety....

    ground is required for both operation and safety. only if the outlets have a real ground and not connected to the neutral. the best is a extra ground rod about 6 feet long in the soil or second best...
  11. Replies
    6
    Views
    1,857

    I am using granite 2 part epoxy glue for granite...

    I am using granite 2 part epoxy glue for granite maybe a countertop shop near you has some for you or you can buy them online ebay or so like this
    ...
  12. Replies
    7
    Views
    2,351

    yes you can if you buy the acrylic version at HD,...

    yes you can if you buy the acrylic version at HD, mostly called " acrylit"
    greetings
  13. Replies
    20
    Views
    5,683

    hi all here are two picture from my igloo but...

    hi all
    here are two picture from my igloo but they projecting different scenes in the whole room walls and ceiling
    with polar bear or stars
    greetings
    waltfl
  14. hi all my experience with laser tubes is that...

    hi all
    my experience with laser tubes is that the tubes are made at "north branch" are the best I have two over three years and both lasted way over 2.000 hours with power out put new close to 45 W...
  15. Replies
    6
    Views
    3,278

    WOW 10.000 SF is a lot, can you not enclose...

    WOW
    10.000 SF is a lot, can you not enclose your area to separate it a bit from the remaining, maybe thick tarp . then a Big window AC ( must be vented to the outside) and a industrial fan.
    but be...
  16. Replies
    20
    Views
    5,683

    hi junioe they are way to expensive. I pay for...

    hi junioe
    they are way to expensive. I pay for 5m roll super bright 5050 LED strips only $ 9.00 including shipping.
    greetings
    waltfl
  17. Replies
    20
    Views
    5,683

    hi gozzie I buy mostly rolls of the LED strips...

    hi gozzie
    I buy mostly rolls of the LED strips from the cheapest seller on ebay, because they all from the same manufacturer.
    right now I use the new remote control for the strips and they work...
  18. Replies
    20
    Views
    5,683

    hi all the picture is the 2.4mm acrylate what I...

    hi all
    the picture is the 2.4mm acrylate what I get left overs from ACE hardware store for free. the LED light stand are three pieces of different wood ( red cedar and bass wood) they are cut to...
  19. Replies
    20
    Views
    5,683

    they are very nice here are a few of my...

    they are very nice
    here are a few of my nightlights, they are all free standing with120V adapter
    greetings
    waltfl
  20. Replies
    13
    Views
    2,952

    hi there first I am cutting up to 6mm black...

    hi there
    first I am cutting up to 6mm black cherry even knotted and black walnut with my 40w machine 70% power and 6to 9mm/s speed and no problem,
    there is something wrong with his machine...
  21. Replies
    62
    Views
    15,151

    hi did you check if the AC is on the HV...

    hi
    did you check if the AC is on the HV powersupply? next step would be to open the HV powersupply and look in the front somewhere there is a glass or ceramic fuse test it if it is blown. be...
  22. Replies
    14
    Views
    5,398

    hi I use the leather protection spray what work...

    hi
    I use the leather protection spray what work pretty good to especially an natural tan leather
    greetings
    waltfl
  23. Replies
    2
    Views
    860

    Merry christmass to all

    I wish everybody a merry Christmas and a happy new year

    waltfl
  24. Replies
    1
    Views
    975

    Does anybody what font it is?

    302055

    Hi all
    does anybody know what font this is?
    greetings
    waltfl
  25. hi there send me a PM with your email and I can...

    hi there
    send me a PM with your email and I can send you a few picture and files
    greetings
    waltfl
Results 1 to 25 of 282
Page 1 of 12 1 2 3 4