Search:

Type: Posts; User: Rick Potter; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Hey Greg.... Do you happen to have that Kapex...

    Hey Greg....

    Do you happen to have that Kapex setup on a DeWalt miter saw? If so, do you have a pic?
  2. Nice to hear a success story. I wouldn't be...

    Nice to hear a success story. I wouldn't be surprised if you could sell the old fence for a few bucks on CL. It is probably better than a lot of old Sears saws out there.
  3. Replies
    31
    Views
    1,903

    I grew up in Cleveland. In the 50's the only...

    I grew up in Cleveland. In the 50's the only place to buy booze was in a 'State Store', which I assume was run by the state.

    I remember going on vacations out of state, and asking my dad what a...
  4. Replies
    18
    Views
    902

    I have a nice older computer with XP. Does it...

    I have a nice older computer with XP. Does it work on that?

    Thanks,
    Rick
  5. Replies
    8
    Views
    747

    Got to hide this thread from wife.........

    Got to hide this thread from wife.........
  6. Replies
    36
    Views
    2,740

    I also have the Freud, and I think I prefer the...

    I also have the Freud, and I think I prefer the DeWalt. The Freud seemed to dull pretty fast cutting melamine. It is available in two tooth counts though. Got mine at Rockler, I think I saw some...
  7. I am certainly not a pro painter, but I do have...

    I am certainly not a pro painter, but I do have several rentals which I have painted both ways. I used to have a nice pro airless, but when it took a dump in the middle of spraying eaves, I...
  8. Replies
    26
    Views
    1,860

    Just checked mine. Most are 13" deep, but I made...

    Just checked mine. Most are 13" deep, but I made a couple deeper for space as well as making the run more visually interesting. One, for a microwave is almost 19", another for use with no door and...
  9. Replies
    41
    Views
    3,709

    May I suggest you check out Mike Henderson's...

    May I suggest you check out Mike Henderson's recent thread "Free SS brake". We all like to think it will never happen to us, but as they say...stuff happens.

    I had a slider (Felder), and it is a...
  10. Replies
    46
    Views
    4,170

    Congrats on a wise saw purchase Mike. We all...

    Congrats on a wise saw purchase Mike. We all like to think we will not make a mistake, but deep down, we all know that accidents happen. Glad it was a minor cut.

    I am gonna make a quickie sled...
  11. Replies
    27
    Views
    2,379

    Haven't got it yet, but look forward to getting...

    Haven't got it yet, but look forward to getting some of those stick on zero clearance insert tapes for the chop saw. They look like they will be very usefull.
  12. Replies
    53
    Views
    7,114

    On the subject of why did the saw fire on a...

    On the subject of why did the saw fire on a little staple, I would think one end of the staple encountered the blade while the other end of the staple touched the table, completing the circuit.
    ...
  13. Replies
    53
    Views
    7,114

    I want to thank Jay for posting about this. May...

    I want to thank Jay for posting about this. May I suggest we not try to assign blame, but use this thread as a learning experience about WHY it happened. I am certainly learning.

    Rick
    ...
  14. Replies
    18
    Views
    2,948

    I hadn't noticed the air clamp Larry used on his...

    I hadn't noticed the air clamp Larry used on his until rereading this thread today. Interesting idea on the fence bolts too.

    Too cool dude.
  15. Replies
    53
    Views
    7,114

    I just have to ask. 12 TEETH? Does that include...

    I just have to ask. 12 TEETH? Does that include chipper teeth? What I am wondering is how much of a revolution did it take to stop that dado blade? I realize it would include both outside blade...
  16. Replies
    13
    Views
    963

    I have a right tilt Unisaw with a Unifence. Had...

    I have a right tilt Unisaw with a Unifence. Had it for over 20 years, and in all that time I wished it was left tilt a total of ONCE. The left side of the fence rail is cut short for a Jessem...
  17. Replies
    40
    Views
    2,917

    I saw an article on shop vacs in a magazine last...

    I saw an article on shop vacs in a magazine last year. Can't remember which one, but I do remember that they liked the Sears big one the best.
  18. Along with above concerns, we have to factor in...

    Along with above concerns, we have to factor in changing conditions in 'emerging nations'. Older creekers will remember the 1950's when some really low quality stuff was made in Japan. It got so...
  19. Replies
    29
    Views
    1,820

    Like Bruce said....Awesome cleaner (on Freuds...

    Like Bruce said....Awesome cleaner (on Freuds list of recommended products). I just put the blade in a cheap dollar store oil drain pan (takes up to 12"), spray on the cleaner and use an automotive...
  20. Replies
    8
    Views
    761

    Hi Matt, She is not a UVA student. Most of...

    Hi Matt,

    She is not a UVA student. Most of the people on the trip were from all over the place, including some Australians. Brit went to school on campus at Grand Canyon U. in Phoenix her first...
  21. Replies
    8
    Views
    761

    The camel's name was Phillip

    Mike Henderson's thread on trip insurance prompts me to write this, but I didn't want to step on his thread. Lean back and relax, this will not be short.

    My Grand Daughter Brittney is 20 years...
  22. Replies
    17
    Views
    1,339

    I have a medium duty shaper, as well as a router...

    I have a medium duty shaper, as well as a router table. I have put router bits in the shaper for years, with good results. I make all my raised panels in the shaper with router bits. I set up two...
  23. Replies
    18
    Views
    1,528

    Here is another pic, if I can get it to work. It...

    Here is another pic, if I can get it to work. It shows the boom that I can use for sanding or my track saw.


    336553

    Obviously, I am not good at this picture thing.
  24. Replies
    18
    Views
    1,528

    Here is mine. Sorry, the pics went haywire. I...

    Here is mine.

    Sorry, the pics went haywire. I also have a Shopsmith vac, shown, which is pretty good for running around the shop.
  25. Hi Don, Fastcap makes a neat brush that you...

    Hi Don,

    Fastcap makes a neat brush that you can wrap around the end of your metal inlet. It would hang down and close up the gap, and still allow work to travel under it. They make it for use on...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4