Search:

Type: Posts; User: Jerry Bruette; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    59
    Views
    2,337

    I've never seen a grinding wheel blow up myself,...

    I've never seen a grinding wheel blow up myself, but I've seen pictures it's impressive and scary.

    When I was in the Navy our ship was contacted for aid to a civilian commercial ship. A grinding...
  2. Why do you feel that you need grade 8 bolts? It's...

    Why do you feel that you need grade 8 bolts? It's not like there'll be a lot of pressure on the table top. Can you even reach the torque spec for a grade 8 in the cast iron top without pulling the...
  3. Your explanation works. I'll have to say that I...

    Your explanation works. I'll have to say that I understand, but it doesn't make sense. I don't know why they would build it in such a way that it's nearly impossible to get any lubrication into that...
  4. I don't see where an oillite bushing would fit in...

    I don't see where an oillite bushing would fit in there and I don't see anyway to lubricate that shaft. I'm guessing the shaft galling and snapping off could be a common problem on that machine.
    ...
  5. Replies
    6
    Views
    378

    Rail and Stile Orientation

    Do the outer stiles on a cabinet always go full height or can they sit on the rails like the inner stiles?

    This is for a stand alone TV cabinet, not kitchen cabs.

    What is the reason for the...
  6. How about pictures of the ends of the roller...

    How about pictures of the ends of the roller shaft that go into the bearings? We could give better advice on their condition if we can see them.
  7. I'd take the sprocket, spring, and chain to...

    I'd take the sprocket, spring, and chain to Motion Ind. They will measure for you and match what you have. They can help with the bushing/bearing for the roller shaft too.

    Is the bearing a brass...
  8. Replies
    114
    Views
    3,869

    The advice I get here, and most of it is pretty...

    The advice I get here, and most of it is pretty darn good, is still pretty cheap.

    And the advice I give is dirt cheap.
  9. If that number is on the sprocket, it would mean...

    If that number is on the sprocket, it would mean it's a double sprocket with 27 teeth.
  10. Sue, I don't know your location but if you have a...

    Sue, I don't know your location but if you have a Motion Industries, Kaman, or other industrial repair parts supplier in your area you could take the chain and sprockets to them and they will help...
  11. Photos can be sent as an attachment. You can't...

    Photos can be sent as an attachment. You can't see them unless you're a contributor, and it's worth the six bucks.
  12. Replies
    14
    Views
    977

    Thanks everybody. Files and chisels I have and...

    Thanks everybody. Files and chisels I have and I'll save the 12 bucks for something else.
  13. Replies
    14
    Views
    977

    Iron On Edging

    I have a project coming up that will need some iron on edging on plywood.

    Should I buy the trimming tool or is there a better way to trim the edging?
  14. Replies
    31
    Views
    2,366

    I got duct seal at Menards in the electrical...

    I got duct seal at Menards in the electrical department. Lowes or Home Depot may have it. It's used for sealing up conduit in a box. You just work it with your hands like modeling clay and stuff it...
  15. The "benchcrafted" tool is a carbide paring...

    The "benchcrafted" tool is a carbide paring scraper, according to their website.
  16. Replies
    22
    Views
    1,695

    Hot water heater always gets me.

    Hot water heater always gets me.
  17. Replies
    11
    Views
    752

    Ad Blockers

    Don't know anything about them, but I'd like to get one. I use Chrome as a browser. Should I go the the Chrome Store and pick one or is there something better.

    I'm open to an education and...
  18. Replies
    24
    Views
    1,723

    They dinged it, they fix and warranty the fix.

    They dinged it, they fix and warranty the fix.
  19. I've thought of a fix that would eliminate the...

    I've thought of a fix that would eliminate the throat plate altogether.

    A piece of 1/4 inch thick aluminum plate with a hole bored in it for the spindle and a counterbore for the different size...
  20. Could, but I'd have to take it off the fliptop....

    Could, but I'd have to take it off the fliptop. I'm not in that big of a hurry. I'd like to think about this for a while and see if there might be something more durable/permanent.
  21. Might be a while before I try a fix. The sander...

    Might be a while before I try a fix. The sander is in the garage and it's only in the 40's for high temps.
  22. Need help with Ridgid Oscillating Sander

    Not a good week, first the combo square and now the sander. Somehow I've managed to let the belt run too low and ground off the posts for leveling the throat plate for the spindle sander.

    Am I...
  23. That's a fairly new saw isn't it? If it's still...

    That's a fairly new saw isn't it? If it's still under warranty a call to SawStop might get you a solution.
  24. Guys an amateur. Shouldn't have taken anymore...

    Guys an amateur. Shouldn't have taken anymore than three hits with a hammer that big.:eek:
  25. Replies
    20
    Views
    1,372

    Well this caveman rubbed a file against a socket...

    Well this caveman rubbed a file against a socket head screw this afternoon. Cobbled one together and it works. It's yet to be seen how long it will last.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4