Search:

Type: Posts; User: Bruce Page; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.57 seconds.

  1. Google PEM Nuts. They are intended for sheet...

    Google PEM Nuts. They are intended for sheet metal use but there might be something you could use.
  2. Replies
    11
    Views
    207

    High quality comes at a price and Microfence...

    High quality comes at a price and Microfence makes very high quality tools. I liked their Bosch Colt base so much I made one for myself based on their design.
  3. Very realistic. How big is it?

    Very realistic. How big is it?
  4. Replies
    25
    Views
    1,194

    I once followed a vehicle hit & run driver so my...

    I once followed a vehicle hit & run driver so my wife could get the license plate number. I'm not sure I would do that today.
  5. Replies
    9
    Views
    328

    Take it back. I had a 8" Delta with a wobbly...

    Take it back. I had a 8" Delta with a wobbly wheel. Nothing I could do to fix it. I later discovered it had a slightly bent shaft but it was enough to cause the wobble 4" from the shaft center...
  6. Replies
    6
    Views
    237

    Send Keith Outten...

    Send Keith Outten, Administrator a PM. He can make the change for you.
  7. Replies
    7
    Views
    448

    It could be the collet or you might have an...

    It could be the collet or you might have an undersized bit. Do you have any way to accurately measure it?
    You should also try thoroughly cleaning the collet assembly with acetone or some other...
  8. Search Indicator tips on Amazon.com There are...

    Search Indicator tips on Amazon.com
    There are dozens to chose from.
  9. Replies
    8
    Views
    437

    "Savart’s Wheel, designed by Bart Hopkin, is...

    "Savart’s Wheel, designed by Bart Hopkin, is widely acclaimed for the fact that it makes the most obtrusive, obnoxious and irritating sound ever known."

    I couldn't have said it any better.
  10. Replies
    5
    Views
    395

    Mike, I'm seeing 3 very nice bowls in your post.

    Mike, I'm seeing 3 very nice bowls in your post.
  11. Replies
    33
    Views
    1,441

    :confused: Clicking on the YouTube icon, lower...

    :confused: Clicking on the YouTube icon, lower right of the video above will take you to the video on YouTube. Comment section's below video.


    Here's what he said:

    ShabbyChicguitars...
  12. Replies
    33
    Views
    1,441

    If you go to YouTube and read the comments he...

    If you go to YouTube and read the comments he says it was because there wasn't enough tension on the blade.
  13. Replies
    17
    Views
    1,769

    What, you don't think Thomas Chippendale had a...

    What, you don't think Thomas Chippendale had a Dremel? :rolleyes:
  14. Replies
    33
    Views
    1,441

    I'm assuming he meant to link to this video. ...

    I'm assuming he meant to link to this video.


    https://www.youtube.com/watch?v=YqkpxKWKkME
  15. Replies
    16
    Views
    770

    They went to a lot of trouble not to give you a...

    They went to a lot of trouble not to give you a yes or no. I would be worried. :rolleyes:
  16. Very nice, worthy of a better quality pic.:)

    Very nice, worthy of a better quality pic.:)
  17. Replies
    14
    Views
    685

    On the flip side, I like to say When you're...

    On the flip side, I like to say When you're retired Every day is Saturday. Saturday was the day we always looked forward to.
  18. Replies
    8
    Views
    842

    That looks great. Good lighting becomes more...

    That looks great. Good lighting becomes more important as the years pass by. You can never have too much light!
  19. Replies
    10
    Views
    452

    Peachtree has decent prices....

    Peachtree has decent prices.
    http://ptreeusa.com/ttrackproducts.htm#1018
  20. Thread: Coasters

    by Bruce Page
    Replies
    2
    Views
    328

    Tim, have you worked through the Vectric V-Carve...

    Tim, have you worked through the Vectric V-Carve tutorials? There are several projects on their free projects page: http://www.vectric.com/cool-stuff/projects.html The Vectric Labs Blog also has...
  21. Replies
    14
    Views
    685

    Jim, a huge congrats to you! You will enjoy it...

    Jim, a huge congrats to you! You will enjoy it immensely. Last Dec 31st makes 4 years for me, 2 for LOML. There is no way we could rejoin the rat race.
  22. Proud indeed! I just keep sayin' WOW! with each...

    Proud indeed! I just keep sayin' WOW! with each picture. When will you be moving in?
  23. Replies
    16
    Views
    1,062

    When you align the miter slot to the blade are...

    When you align the miter slot to the blade are you using the same spot on the blade? You should mark a dot on your blade with a pencil/sharpie and zero your indicator on the dot. Rotate the blade...
  24. Replies
    16
    Views
    1,062

    It has the Biesemeyer fence, right? Check your...

    It has the Biesemeyer fence, right? Check your manual, the fence is adjustable.
  25. Replies
    4
    Views
    385

    Square corners are pretty easy to generate using...

    Square corners are pretty easy to generate using a v-bit in V-Carve or Aspire but I don't think it can be done using a full bull nose bit like that. I'm sure it could be modeled in Aspire using a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4