Search:

Type: Posts; User: Al Sherred; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: stain color

    by Al Sherred
    Replies
    7
    Views
    1,142

    stain color

    I will make some samples and see what the wife likes best. Thanks for your suggestion
  2. Thread: stain color

    by Al Sherred
    Replies
    7
    Views
    1,142

    stain

    I will put a finish on it. I did't think about it rubbing off onto things, thanks for that information.
  3. Thread: stain color

    by Al Sherred
    Replies
    7
    Views
    1,142

    color

    Thanks for your input. My wife is thinking about red mahogany, we will see, I will make some samples of colors.
  4. Thread: stain color

    by Al Sherred
    Replies
    7
    Views
    1,142

    stain color

    I have a porch glider that is made of tubular steel,the color is gray , a little darker than battleship gray. I have made replacement slats for the seat area, 13 in all 2x58.5x3/4 out of white oak....
  5. Thread: glider

    by Al Sherred
    Replies
    5
    Views
    1,051

    glider

    Thanks for the reply I have been thinking of using white oak, I have since had the frame blasted and powder coated Grey even though the pic looks a little purple. Im trying to decide how to finish...
  6. Thread: glider

    by Al Sherred
    Replies
    5
    Views
    1,051

    glider

    I have this old glider, and was wondering if someone could identify the wood.
  7. Thread: T/S fence

    by Al Sherred
    Replies
    6
    Views
    1,067

    I think I may have this issue solved. I adjusted...

    I think I may have this issue solved. I adjusted the fence to the point that it was tight against the rail, then the lock handle was way to tight, so I backed the adj screws off a quarter turn, the...
  8. Thread: T/S fence

    by Al Sherred
    Replies
    6
    Views
    1,067

    T/S fence

    I have a shop fox fence (W2005) on my G1023SL table saw, and I set the fence on say 6" and lock the fence down and measure the distance again and it is 5 15/16. I have been adjusting the fence...
  9. Thread: Table

    by Al Sherred
    Replies
    4
    Views
    2,002

    Thanks Barry. I didn't seal the table prior to...

    Thanks Barry. I didn't seal the table prior to applying the resin, I had to sand for more than a hour to remove all the overspill . I used easy cast resin and glow powder I found on Amazon . I...
  10. Thread: Table

    by Al Sherred
    Replies
    4
    Views
    2,002

    I sanded it from 80 grit through 400 grit and 5...

    I sanded it from 80 grit through 400 grit and 5 coats of high gloss lacquer.
  11. Thread: Table

    by Al Sherred
    Replies
    4
    Views
    2,002

    Table

    My daughter sent me a video of a table that she liked and I thought since her birthday is in May I would give it a try, this is how it ended up.

    The first pic is the table by day, the second one...
  12. Replies
    6
    Views
    2,060

    its will get a skirt

    Thanks for the input, that sketchup drawing shows clearly, the table with the skirt is easier on the eyes.
  13. Replies
    6
    Views
    2,060

    Skirt or no skirt

    I have a table that I have been working on. I have a top that is 41in long 17wd and 7/8in thick, the legs are tapered on all sides. the legs will be attached with cinch plates to the bottom of table...
  14. Replies
    32
    Views
    4,910

    Um

    This post has nothing to do with bragging, or stroking my ego , it was intended strictly for a safety concern. Since I hear all the time about such things as kickback and the damage caused by such...
  15. Replies
    32
    Views
    4,910

    I measured with a digital caliper. It must be...

    I measured with a digital caliper. It must be good enough ,it sure seemed to go through the blade very nicely. Thanks for the replies.
  16. Replies
    32
    Views
    4,910

    Thanks for the reply. I ask this question...

    Thanks for the reply. I ask this question because I just went through all the alignment checks, miter slot to blade, blade to fence, and so forth, and I had to adjust my miter slot to the blade, and...
  17. Replies
    32
    Views
    4,910

    Rip measurements

    After ripping a board ,and measuring the width along the length what is an acceptable amount of deviation on the deminsion?
  18. Resolved

    Biscuit jointer is working. I sent an email to Freud and a few days later I recieved a reply requesting me to call a toll free number which I did and a very knowledgable fellow told me a story of an...
  19. still no go

    Thanks for the suggestion, cleaned the armature and brushes. I have traced the power to the connector to the brushes but that is where I stop. I guess having it sit idle for such a long while wasnt...
  20. I have a multimeter and I have power to the...

    I have a multimeter and I have power to the switch and then from there I have power to the connections at the armature brushes but that is where I get lost I don't know what to do next other than...
  21. Freud js-102 biscuit jointer electrical woes

    I have a Freud js-102 biscuit jointer, I have had it for a number of years, but used very very little maybe 20 biscuits cut with it. It's been sitting in its case unused for years. I now have a...
  22. Replies
    7
    Views
    1,747

    Thank You for the replies, I ended up, doing...

    Thank You for the replies, I ended up, doing basically what Jon said, put tape over the cutout spots and marked them then just used the jig saw. I was fretting about the cut being clean and I really...
  23. Replies
    7
    Views
    1,747

    Cutting holes

    I would like some ideas for the easiest way to cut multiple,rectangular holes in 1/4 inch plywood actually it's .190 thick. The cutouts are for windows in a doll house. My brain takes me to...
  24. Replies
    4
    Views
    1,416

    twins for twins

    I made these for a very nice lady, that knows someone who just had twins and wanted to give her a pair of rocking horses. I used plans from woodcraft merrilegs. 286623
  25. Replies
    4
    Views
    1,443

    Manual

    Thanks Bill, I will check for one. The problem has been found, Patrick got it correct the nut on the top of the spindle pulley came loose. Thanks for all the possibilities
Results 1 to 25 of 40
Page 1 of 2 1 2