Search:

Type: Posts; User: Ed Gibbons; Keyword(s):

Page 1 of 17 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    21
    Views
    1,841

    I ended up buying a piece of 1/4” plexiglass and...

    I ended up buying a piece of 1/4” plexiglass and plan to make my own. The Woodpecker plate looks awesome but the cost plus shipping in almost as much as what I paid for the router. The 6-1 jig looks...
  2. Replies
    49
    Views
    4,415

    Keep it in the shop for at least a week.

    Keep it in the shop for at least a week.
  3. Replies
    21
    Views
    1,841

    Router Base Plate

    Just received the Bosch Colt router. I would like to purchase an aftermarket baseplate which is larger. Goal is to add stability. Suggestions appreciated.
  4. Replies
    11
    Views
    1,085

    Sharpening Blades

    Who do you send your blades out for sharpening?
  5. Replies
    2
    Views
    457

    Gluing Dado Joint

    My project calls for the dado to be 1/4” deep. Should I make it bigger to account for the glue?
  6. Replies
    18
    Views
    2,156

    Jim, What gauge is your no name staple gun?

    Jim,
    What gauge is your no name staple gun?
  7. Replies
    8
    Views
    1,528

    Rockler Router Bits

    Who makes them? Are they worth buying?
  8. Replies
    8
    Views
    1,196

    Bandsaw Blade

    What is the best overall blade?
  9. Replies
    4
    Views
    1,677

    Garage Doors

    I will be painting aluminum garage doors. Should I prime them first? Any feedback would be appreciated.
  10. Replies
    10
    Views
    5,874

    I live near State College, PA. Does anyone live...

    I live near State College, PA. Does anyone live nearby with a laser that I could observe the process?
  11. Replies
    10
    Views
    5,874

    Co2 laser I saw starts at $5000. That’s a bit...

    Co2 laser I saw starts at $5000. That’s a bit more than I planned on spending.
  12. Replies
    10
    Views
    5,874

    What do I need?

    I want to get into laser engraving. Looking to do wall plaques, etc. Research has brought me to xTool. What will I need? Hardware, software, etc? I’m willing to pay a little more because I have...
  13. Replies
    11
    Views
    1,392

    Flush Trimming Router Bit

    I’m using a router table to flush trim edges on a template. What would be the best and safest bit to use. I read some info about compression bits.
  14. Replies
    12
    Views
    4,107

    Not looking to go into production; plan is being...

    Not looking to go into production; plan is being a hobbyist. But I’ve learned that most times for a few more dollars, the value and potential is greater.
  15. Replies
    12
    Views
    4,107

    Engraver Recommendation

    Looking to get into engraving on wood. Looking for recommendations on how to get started.
  16. Replies
    6
    Views
    1,543

    Flooded the area and wiped it off after 15...

    Flooded the area and wiped it off after 15 minutes.
  17. Replies
    6
    Views
    1,543

    BLO Dry Time

    How long should I wait to put an oil based topcoat after applying boiled linseed oil to pop the grain?
  18. Replies
    14
    Views
    1,611

    It is a small DeWalt handheld router that accepts...

    It is a small DeWalt handheld router that accepts a 1/4 inch shaft. I completely loosen the nut. Definitely want to keep metal away from the bits. Thanks for the feedback. I think I will take...
  19. Replies
    14
    Views
    1,611

    Router Help Needed

    Even when I have completely loosened the collet, it’s very difficult to remove the bit. I need to use a flathead screwdriver to release the bit.
    Suggestions appreciated.
  20. Replies
    12
    Views
    1,255

    I will be using a hand held router. I made a...

    I will be using a hand held router. I made a template out of 3/4 ply that I will place against a 3/4 piece of walnut.
  21. Replies
    12
    Views
    1,255

    Flush Trimming bit

    Looking forward a recommendation for a flush trimming bit.
  22. Replies
    6
    Views
    1,212

    No problem. Just don’t want to use the incorrect...

    No problem. Just don’t want to use the incorrect paint and have future problems. From what I have researched, like all painting, it’s all about the prep.
  23. Replies
    6
    Views
    1,212

    Bathroom Paint

    Can regular paint be used for a bathroom?
  24. Replies
    7
    Views
    921

    Grizzly Planer Question

    On my Grizzly planer, I’m the middle of the top is a piece of plastic that impacts the depth of cut. Anyone
    with this planer, have you removed the plastic?



    474313
  25. Replies
    23
    Views
    2,831

    Definitely overkill on the grit sequence. I...

    Definitely overkill on the grit sequence. I wanted to take off as much of the finish as I could without scratching the wood. Definitely the lower grits took off more but the higher grits appeared to...
Results 1 to 25 of 417
Page 1 of 17 1 2 3 4