Search:

Type: Posts; User: Jared Cuneo; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    1,015

    Thanks for the input. I ordered a solid pulley...

    Thanks for the input. I ordered a solid pulley from Inline today and a new link belt for giggles. Will report back in case someone else has issues.

    If you have a delta contractor, I recommend that...
  2. Replies
    3
    Views
    1,015

    Delta Contractor Arbor problem

    Friends, I have a delta contractor with the 2 piece pulley and noticed after a cross country move that it was cutting rough. After installing PALS, link belt etc, I still could not get a good cut....
  3. Replies
    4
    Views
    1,219

    Marquetry help

    I recently did some of my first marquetry projects using beech and walnut burl which were fairly easy to cut.

    I went to attempt some purpleheart pieces and had a rude awakening. It (and several...
  4. To answer your question, yes, they offer one. In...

    To answer your question, yes, they offer one. In fact, I have cast iron wings on my Delta 10" Contractor.

    JC
  5. Replies
    41
    Views
    9,691

    What a great saw. Too bad some extra safety is...

    What a great saw. Too bad some extra safety is out of my price range :(

    JC
  6. Well, I feel like a moron, I went and measured...

    Well, I feel like a moron, I went and measured slot to blade clearance and it was off!

    About a month ago, I was getting crazy errors when cutting at 45 degrees. Turned out I needed to shim my...
  7. I'm using a bies fence, it's pretty solid...can I...

    I'm using a bies fence, it's pretty solid...can I check it somehow? It's straight if I hold a long edge next to it...

    Thanks!
  8. Table saw nibbling end of ripped boards

    My Delta Contractor is nibbling a 64th or so (sometimes a 32nd) off the trailing end of ripped boards on the fence side.

    The pattern is visible on the last 3/8 in of the board on the side of the...
  9. Replies
    7
    Views
    1,367

    I just went through this with my Delta...

    I just went through this with my Delta contractor....and I have no dial indicator, just a starrett combo square.....I'd be willing to bet that I am around .002-.004 and thats good enough for me.....I...
  10. Update and questions about shimming trunnion

    Well, I bit the bullet and added the shims to the rear trunnion of my Delta contractor.

    The heeling at 45° is virtually gone now (it was almost 1/16"!) but my 90° setting is out about .002-.004 (I...
  11. I think I am going to try to get it aligned...

    I think I am going to try to get it aligned tonight. Don't be surprised if my next thread is titled, 'Help, I've f*d up my delta contractor'

    :)
  12. Replies
    3
    Views
    814

    Ok, time to adjust the trunnions

    I've discovered that my wonky bevel cuts are caused by bad trunnion alignment and that I need to shim the rear trunnion on my Delta contractor saw. FYI, on my left tilt saw (fence to right of blade),...
  13. Blade heeling out on tilt - Delta Contractor

    I searched for this topic but only saw responses to fixed a heeled blade at 90 degrees.

    My blade is perfect when at 90, but as I tilt, the back of the blade heels toward the fence....It's fairly...
  14. Replies
    3
    Views
    842

    Guesses on how this rail is attached?

    Anyone know the strongest way to attach the top rails (the crown part) on these head and footboards?

    Thanks!

    JC
  15. Replies
    7
    Views
    1,036

    Hehe, had I not paid $100 for that blade (WWII),...

    Hehe, had I not paid $100 for that blade (WWII), I probably would not have either :)

    JC
  16. Replies
    7
    Views
    1,036

    Help ease my mind with TS issue

    Today I made a new aux fence for my miter gauge and faced it with some sticky 220 sandpaper. I assembled, then ran it through the saw to precut the kerfs and knock the ends off at 45 degree angles.
    ...
  17. Replies
    4
    Views
    908

    Hmm, ok Glenn, I'll try to tint some minwax with...

    Hmm, ok Glenn, I'll try to tint some minwax with the dyes and report back....Otherwise, I will use the artist colors....

    Thanks!

    JC
  18. Replies
    4
    Views
    908

    Tinting your own wax?

    I have need for some dark wax but not really into spending $20 for a whole 12 ounces of wax which I will use infrequently. I do have various colors of transtint dyes and I was wondering if anyone has...
  19. Replies
    14
    Views
    21,168

    Wow, thats a generous offer....I'd like to check...

    Wow, thats a generous offer....I'd like to check that out too....

    JC
  20. Replies
    6
    Views
    2,998

    That's a very good point about pressure that Will...

    That's a very good point about pressure that Will has raised. This alone would deter me from buying it had I known.....Oh well, that was before I found all the WW internet communities....
  21. Replies
    6
    Views
    2,998

    I have the Pinnacle and its a pain in the butt to...

    I have the Pinnacle and its a pain in the butt to use unless you are solely doing plane irons or long chisels.

    I would go with the stones and the veritas MKII guide (which I also have). I like...
  22. Replies
    18
    Views
    2,624

    It's been stated, but I would reiterate....no...

    It's been stated, but I would reiterate....no matter how you choose to proceed you should stop to take some measurements. I would see if you have 4 square stock first of all. Then, I would examine...
  23. Replies
    8
    Views
    2,466

    Excellent! JC

    Excellent!

    JC
  24. Replies
    3
    Views
    1,402

    I think you will want to look at a product called...

    I think you will want to look at a product called Rockhard Varnish.....

    JC
  25. Replies
    3
    Views
    895

    Hmm, never thought of that. Will definitely try...

    Hmm, never thought of that. Will definitely try that one....Thanks Dennis.

    JC
Results 1 to 25 of 166
Page 1 of 7 1 2 3 4