Search:

Type: Posts; User: Greg Cole; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.25 seconds.

  1. Thread: Desk

    by Greg Cole
    Replies
    36
    Views
    8,158

    Whoa, thats AWESOME Alex. The e-mailed progress...

    Whoa, thats AWESOME Alex.
    The e-mailed progress pics showed me it was going to be nice.. but with the finish applied.... all I can say is WHOA.
  2. Replies
    15
    Views
    2,936

    Or if ya don't have the time to do it right, do...

    Or if ya don't have the time to do it right, do you have the time to do it twice? :D
  3. Replies
    3
    Views
    2,160

    I made my bench with a premade hard maple top I...

    I made my bench with a premade hard maple top I bought from McMaster Carr. As Alex said, I added a skirt around all sides as well. It took a little work to flatten it, but other than that it's been...
  4. Replies
    9
    Views
    3,229

    Nice to see you around again Per. Lookin' at...

    Nice to see you around again Per. Lookin' at those bar pics never gets old. ;)
  5. Replies
    24
    Views
    2,739

    Welp, me thinks Joe's got it right here. D'oh....

    Welp, me thinks Joe's got it right here. D'oh. :mad:
    Seems as once a month since March I've had one large unplanned expense a month... I was hoping to get through June without.:rolleyes:
  6. Replies
    24
    Views
    2,739

    There's no frost anywhere. Plenty of CFM's in the...

    There's no frost anywhere. Plenty of CFM's in the registers... so the a coil isn't plugged. The filter is brandy new as well. Anyway... my thought on the intermittent cooling was MAYBE the contactor...
  7. Replies
    24
    Views
    2,739

    The unit doesn't stop, it just seems to stop...

    The unit doesn't stop, it just seems to stop putting out cold air after a few hours of running. :confused: The condenser and fan still run and will stay running for hours. If I shut the AC off for an...
  8. Replies
    24
    Views
    2,739

    The compressor starts and stays on when the unit...

    The compressor starts and stays on when the unit cycles.
    I work with alot of industrial machinery and can read prints, check the cap's etc. Kinda scratching my noodle here about it....:confused:
    I...
  9. Replies
    11
    Views
    6,405

    Absolutely, spray foam for insulation. Heck of an...

    Absolutely, spray foam for insulation. Heck of an R value (depending on what foam and how thick). Ask Mike Holmes about it, or if ya have seen Holmes on Homes..... ;)
    If you want to ship lap your...
  10. Replies
    24
    Views
    2,739

    AC/HVAC Folks

    So.... I'll try to keep it short. :rolleyes:
    Here's the problem..... during peak times, the AC unit seems to only be pumping room temp air through the house. When it's 88 outside at 1pm, it's 88...
  11. Replies
    9
    Views
    2,637

    Looks good Alex. I have a small assembly table...

    Looks good Alex.
    I have a small assembly table directly behind my bench that I put all the hand tools on when working on the bench.
    Looks like the clamp collection has grown quite a bit too. ;)
  12. Bandsaws need to be set up properly to get good...

    Bandsaws need to be set up properly to get good results, not saying yours isn't. Buy one of the Bandsaw books from Duginski, read it & then take it to the shop with you if you haven't already.
    Also...
  13. Buy both, set one up with the standard 45* angle...

    Buy both, set one up with the standard 45* angle and set up the other with the 50*.:D Kinda serious actually, buy one LN and then see if you can't get a rust bucket and revive it.
    The only real...
  14. Replies
    10
    Views
    2,060

    +1 on the sanding before assembling. Prefinish...

    +1 on the sanding before assembling.
    Prefinish panels as well to avoid "naked" areas during seasonal movements of the panel.
  15. Replies
    15
    Views
    4,487

    Hey stranger, niiiiiice job. I know I won't be...

    Hey stranger, niiiiiice job.
    I know I won't be showing these to my wifey anytime soon, she'll tell me to put the bows n arrows away and blow the dust off my tools & shop!:eek:
    I haven't been...
  16. Replies
    20
    Views
    4,908

    Very well done, I like it.

    Very well done, I like it.
  17. Replies
    6
    Views
    1,007

    Dan, The scales slide in and out quite handily....

    Dan,
    The scales slide in and out quite handily. I'd just remove the unused ones and the "main" steel scale is held in place by a magnet to you can move-adjust it in seconds.
    I love my incra stuff.
  18. Replies
    18
    Views
    6,247

    Foamboard insulation on any old flat spot. Make...

    Foamboard insulation on any old flat spot.
    Make an outfeed table to match the height of your TS & when you use it to crosscut ply, just toss the foamboard on the top and cut away (just be midful of...
  19. Save yourself the hassle & just take over the...

    Save yourself the hassle & just take over the garage & park the cars outside. :D I used to try to juggle everything around in mine to be able to fit at least one car in there... that got old & a...
  20. Replies
    7
    Views
    2,200

    Hey Alex, you forgot to title the pics "PITA".:D

    Hey Alex, you forgot to title the pics "PITA".:D
  21. Replies
    9
    Views
    1,890

    Another dod lover here. Best wishes to Flabby....

    Another dod lover here. Best wishes to Flabby.
    Our dog (puggle- 1/2 pug & 1/2 beagle mix) was hit by a car at just 6 months old. Roughly $2K later, little Rudy was in a cast and healing. The 2...
  22. Replies
    17
    Views
    2,062

    Very nice Mike. Excellent job on the veneer as...

    Very nice Mike.
    Excellent job on the veneer as always.;)
  23. Replies
    12
    Views
    3,019

    Very nice, love the material. I am sure your...

    Very nice, love the material.
    I am sure your sister will treasure this.
  24. Replies
    16
    Views
    1,951

    +1 to the comment about spending a little time...

    +1 to the comment about spending a little time remodeling the home you just purchased (unless it's new). You will pick up some hands on & some tools and turn the house into your home. Diving right...
  25. Replies
    177
    Views
    54,148

    Matt, What's the FF material? Maple as well?

    Matt,
    What's the FF material? Maple as well?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4