Search:

Type: Posts; User: Wakahisa Shinta; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thanks Stan. I found a gallon worth of it on a...

    Thanks Stan. I found a gallon worth of it on a certain e-commerce site. I were just wondering if people use other type of oil besides the one listed in the manual and on W&H's website.
  2. Pictures may help. Maybe the below may give you...

    Pictures may help. Maybe the below may give you ideas on how to adjust yours.

    455299 455301

    On Felder/Hammer saws, the fence's adjustments are made by manipulating the fence's round-steel rail...
  3. Replies
    35
    Views
    4,837

    Before you buy a Felder machine, become a member...

    Before you buy a Felder machine, become a member of the Felder Owners Group (https://groups.io/g/felderownersgroup). A lot of people can advice you about machine and options there. Occasionally,...
  4. Gear box oil for Williams Hussey molder (model No 154)

    Hello. I recently acquired a Williams Hussey molder, model No. 154 given the serial number in relation to the manuals provided on WH's website. The electronic manual specifies gear oil from WH or...
  5. I see now that I looked at picture #4 more...

    I see now that I looked at picture #4 more closely. Nice machine work! I couldn't tell the suggestion of the mating surfaces at first in that picture until after you answered and I returned for...
  6. Brian, did you machine the L-stop out of one...

    Brian, did you machine the L-stop out of one solid block of brass? I like the pneumatic clamp! I will remember this detail for future reference.
  7. There are a few ways I rip using my KF700SP. ...

    There are a few ways I rip using my KF700SP.

    With two parallel fences (or one flip stop + one parallel fence) attached to the sliding table, the stock is referenced to the parallel fences then...
  8. What are you going to build? Are you going to...

    What are you going to build? Are you going to work with sheet goods, or solid wood, or both? For sheet goods, small shop, and a finite budget, then a good track saw and a small slider are excellent...
  9. Thanks everyone. I measured the "good" oil cup...

    Thanks everyone. I measured the "good" oil cup on my General 220. Though the measurements with a digital caliper is not an exact match with Gits's specs, they are close. Maybe the Gits 00801...
  10. General 220 mortiser oil cup thread size

    Hello,
    I am restoring a General 220 hollow chisel mortiser that once belonged to a high school's woodshop class. It was abused, but still in good shape. There are two oil cups that hold oil for...
  11. I rip using either the sliding table and the rip...

    I rip using either the sliding table and the rip fence, depending on the work flow. You can make you own parallel rip guide for the sliding table with DIY wooden T-nut, scrap woods, etc. before you...
  12. John, what do you use to clean your gun after...

    John, what do you use to clean your gun after spraying Lenmar Duralaq? I read the TDS, but want to hear your real-time method.

    I have been spraying BM Advance with a Fuji Q5 and T75G gun, but...
  13. Replies
    36
    Views
    5,043

    Thank you for your advice and offer of support. ...

    Thank you for your advice and offer of support. Below is more history.

    To answer some of the questions raised previously, the machine impacted twice on its way down to the ground; once when the...
  14. Replies
    36
    Views
    5,043

    A used machine shipping nightmare

    To make a very long story short, I now have a used woodworking machine, about 2100+ pounds in weight, laying upside down in the middle of my driveway with scattered parts here and there, after being...
  15. A main reason I bought the A3-31 with the...

    A main reason I bought the A3-31 with the "Silent" cutter head was because Felder had a showroom near where I lived. After 6 years, I am on the 2nd edge of the cutters and have a set on the shelf...
  16. Replies
    17
    Views
    1,862

    I am curious about a few things. Is that tear...

    I am curious about a few things. Is that tear out in the second picture, mortise #2 from left nearest to the camera position? Is this common for a chain mortiser? Looking at the chain, it seems...
  17. The peripherals for the K3 do not have to be...

    The peripherals for the K3 do not have to be expensive. I modified this clamp to work with the K3. I have two, front and back. I also use these clamps with a wooden T-nut in the slider table's...
  18. A very quick decision. A primer on sliding...

    A very quick decision.

    A primer on sliding table calibration. Link. When I received my K3, it was reasonably calibrated. If you want tighter tolerances, then you will need some basic...
  19. Sign up --> https://groups.io/g/felderownersgroup

    Sign up --> https://groups.io/g/felderownersgroup
  20. Replies
    62
    Views
    10,056

    That secondary saw/blade excels at cutting...

    That secondary saw/blade excels at cutting tenons. Its capabilities are demonstrated in a lot of Ishitani Furniture videos, which are quite relaxing to watch.
  21. Replies
    16
    Views
    1,952

    Brian, these were purchased from Japan tool,...

    Brian, these were purchased from Japan tool, whose store owner is So Yamashita.
  22. Replies
    62
    Views
    10,056

    We really veered off course! Getting back to the...

    We really veered off course! Getting back to the topic of the thread.

    Are the various manufacturers of Japanese short-stroke slider equivalent in quality of their machines?

    The little...
  23. Replies
    34
    Views
    5,291

    This is not too difficult to make from scrap...

    This is not too difficult to make from scrap plywood. I have more than a few, in different lengths, spacing, etc. The longest one is made from a 6-foot 1/2-inch thick plywood scrap, about 10 inch...
  24. Replies
    62
    Views
    10,056

    Mark, my understanding is that Marunaka makes a...

    Mark, my understanding is that Marunaka makes a grinder for the disposable knives. I suppose you can not grind the disposable knives too many times, but how many times can you grind them? Does it...
  25. Replies
    16
    Views
    1,952

    Christopher, the handles are made from rosewood.

    Christopher, the handles are made from rosewood.
Results 1 to 25 of 261
Page 1 of 11 1 2 3 4