Search:

Type: Posts; User: Thomas Heck; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    2,736

    I appreciate the help. I heated it some, sprayed...

    I appreciate the help. I heated it some, sprayed wd 40 around it and finally got it off. Used a couple pry bars and a piece of wood to get it off.
  2. Replies
    7
    Views
    2,736

    I appreciate the advice and the video. Hopefully...

    I appreciate the advice and the video. Hopefully I can get it freed up this evening. It’a so close to the cast iron you don’t have much space to get anything behind it.
  3. Replies
    7
    Views
    2,736

    Thanks for the info. I can only find one grub...

    Thanks for the info. I can only find one grub screw. It is an aluminum pulley. So would a propane torch be good to heat the pulley. Thanks again.
  4. Replies
    7
    Views
    2,736

    Pulley help

    I’m in the process of putting bearings in a Nova 1624-44. The top pulley is not wanting to free up. I removed the screw from the side of the pulley. I’ve been using a small piece of wood and a crow...
  5. Replies
    10
    Views
    2,332

    Talked to Teknatool today. They were very...

    Talked to Teknatool today. They were very apologetic for the long time it’s taken for any response. I was wrong on my warranty. I was thinking 5 yrs, but that’s mechanical. It’s 2 years on...
  6. Replies
    10
    Views
    2,332

    They finally sent an email and said they were on...

    They finally sent an email and said they were on skeleton crew because of holidays. He said he’d get the technician to call ASAP. He apologized for the delay. But still would like to get moving...
  7. Replies
    10
    Views
    2,332

    Nova Customer Support

    Any of you had to deal with nova customer support. I started a ticket with them before Christmas. They have sent emails and called once, but no help. My Dvr upgrade just quit and is still under...
  8. Replies
    11
    Views
    2,518

    Nice work! Color turned out good, yet still...

    Nice work! Color turned out good, yet still shows character of the wood.
  9. Replies
    14
    Views
    2,311

    I got the rubber Chucky seals and they work fine.

    I got the rubber Chucky seals and they work fine.
  10. Replies
    18
    Views
    2,811

    Happy Birthday!

    Happy Birthday!
  11. Thread: Walnut NE

    by Thomas Heck
    Replies
    5
    Views
    1,970

    Nice work! I like the bottom too. I bought a...

    Nice work! I like the bottom too. I bought a custom stamp, but found I often didn't have the bottom flat. So the stamp would rock and not do a good job. I have been engraving which looks ok, but...
  12. Thread: Smock

    by Thomas Heck
    Replies
    23
    Views
    5,837

    I have found from weed eating in an under armour...

    I have found from weed eating in an under armour type shirt, that weeds nor wood chips will stick to this type shirt. I think their made of polyester.
  13. I bought a branding iron that works great, but...

    I bought a branding iron that works great, but only if the bottom is perfectly flat. I rarely use it anymore. I use a Dremel engraver, it cost a lot less than the iron. You can write whatever you...
  14. Replies
    49
    Views
    8,177

    Looks nice to me. You give that to someone as a...

    Looks nice to me. You give that to someone as a gift who isn't a wood turner and they'd love it without looking for flaws. Wood turners can be judge mental comparing works to their own. But no...
  15. Replies
    18
    Views
    2,834

    Works great and simple to use. It has saved me...

    Works great and simple to use. It has saved me lots of money.
  16. Replies
    4
    Views
    1,079

    Nice piece of work!

    Nice piece of work!
  17. Replies
    10
    Views
    2,239

    I ended up getting one that hadn't been tapped. ...

    I ended up getting one that hadn't been tapped. The seller is taking care of it. Thanks for all your help.
  18. Replies
    10
    Views
    2,239

    Did you tap the adapter to screw in the fitting? ...

    Did you tap the adapter to screw in the fitting? My adapter doesn't have threads, so I thought about tapping it for a fitting? Thanks, Thomas
  19. Replies
    10
    Views
    2,239

    Thanks for the pictures. That helps a lot.

    Thanks for the pictures. That helps a lot.
  20. Replies
    10
    Views
    2,239

    Thanks for the info Tom. I ordered it. They said...

    Thanks for the info Tom. I ordered it. They said it was the last one in stock. I may have a few more questions for you when it gets here. Thanks again.
  21. Replies
    10
    Views
    2,239

    Thanks for the reply. I sent you a message.

    Thanks for the reply. I sent you a message.
  22. Replies
    10
    Views
    2,239

    Nova Vacuum Adapter?

    I have found on eBay and a couple other sites a vacuum adapter similar to the one nova discontinued. Does anyone use these or know if they work well. I have the holdfast system and use their...
  23. Replies
    4
    Views
    1,270

    It seemed to work good. I always wiped it on and...

    It seemed to work good. I always wiped it on and used it like a friction polish. Normally the more coats, the better it looked. It took a few days for the smell to go away. Not exactly sure on...
  24. Replies
    4
    Views
    1,270

    Tung Oil Mix Vs BLO Mix

    I'm out of the Tung oil, dna, shellac mix that I've used for awhile and was wondering how it compares to the BLO Mix. I have to order pure Tung oil. I usually get it from woodcraft. But I think I...
  25. Replies
    16
    Views
    3,785

    Thanks Allan. I just started noticing this, it...

    Thanks Allan. I just started noticing this, it hadn't been doing it before.
Results 1 to 25 of 250
Page 1 of 10 1 2 3 4