Search:

Type: Posts; User: Scott Shepherd; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.45 seconds.

  1. Replies
    74
    Views
    2,426

    Errr.....maybe they are designing them in...

    Errr.....maybe they are designing them in Colorado now ;)

    We rented a car not too long ago and got upgraded to their premium vehicle that had all that stuff on it. I was driving the entire trip,...
  2. Congratulations Ron, I'm sure you'll put it to...

    Congratulations Ron, I'm sure you'll put it to good use.
  3. Replies
    3
    Views
    394

    Very nicely done Keith! Very professional looking...

    Very nicely done Keith! Very professional looking installation.
  4. Replies
    25
    Views
    708

    I agree with Mike, you need at least 3 tiers to...

    I agree with Mike, you need at least 3 tiers to your system, if not more. On a hard drive, backed up on archival DVD's, stored off site on a server. It's VERY important that your backup plan includes...
  5. Replies
    27
    Views
    739

    It is until it's your box it won't suck smoke out...

    It is until it's your box it won't suck smoke out of ;)
  6. Replies
    7
    Views
    311

    Kern's are about $100,000 last time I checked...

    Kern's are about $100,000 last time I checked (two weeks ago ;) ).
  7. Replies
    27
    Views
    739

    Bill, their system is lower CFM, but it pulls...

    Bill, their system is lower CFM, but it pulls 5,800 PA, or about 24 inches of water (if I said that right). They said that high static pressure would solve the problem. It didn't. It got worse. The...
  8. Replies
    27
    Views
    739

    I think the number is 580 fpm inside the cabinet....

    I think the number is 580 fpm inside the cabinet. That's where we saw smoke clear on various machines. Forget any numbers I stated earlier, they were from memory (or lack there of). I just watched a...
  9. Replies
    7
    Views
    307

    You have it right.

    You have it right.
  10. Replies
    27
    Views
    739

    I'm not sure I agree with that totally Bill. I...

    I'm not sure I agree with that totally Bill. I agree there is friction loss in pipe, but going from metal to PVC, I can't imagine it's a noticeable difference. In fact, I saw less than 3% difference...
  11. If that's your intent in this business, then I've...

    If that's your intent in this business, then I've offered my last piece of advice to you. I have no desire to help someone undercut someone until they go out of business and then raise their prices...
  12. Replies
    27
    Views
    739

    None of that matters Mark, that's my point. The...

    None of that matters Mark, that's my point. The number of turns and the height different to machine made no difference.

    We had a 2,300 CFM blower hooked up, running over 2 stories of metal pipe,...
  13. I think that's the root of the problem. You don't...

    I think that's the root of the problem. You don't NEED to make it work. Many of us had no choice but to make it work. That meant we found the paths to make us money. Your pricing frightens me. $10...
  14. Replies
    27
    Views
    739

    Mark, I only mentioned those things to illustrate...

    Mark, I only mentioned those things to illustrate that all the things we were told would correct the issues didn't make any measurable difference. In the end, air speed was king and without it, no...
  15. Replies
    14
    Views
    495

    Thanks Bruce, good to know. The place the sword...

    Thanks Bruce, good to know. The place the sword came from, Vanguard, state that they laser engrave theirs, but they only offer 18 characters including spaces, and the customer wants more than 18...
  16. Replies
    27
    Views
    739

    That might be fpm, not fps. I'll see if I can dig...

    That might be fpm, not fps. I'll see if I can dig out my reference material and find it to clarify.
  17. Replies
    27
    Views
    739

    Mark, you lost me on that calculation there. If I...

    Mark, you lost me on that calculation there. If I were to try and explain it, I would botch the technical terms horribly and confuse the issue even greater. I spoke at length with a number of higher...
  18. Replies
    14
    Views
    495

    Here's photos of the actual sword and area to be...

    Here's photos of the actual sword and area to be engraved. So far, no one's been able to tell me anything relative to what can or cannot be put on it (i.e., is there a limit on letters? Font sizes,...
  19. Not a display case, a counter top display. Two...

    Not a display case, a counter top display. Two different things.

    Do you have a website? Business cards?
  20. Without seeing photos, it's impossible for us to...

    Without seeing photos, it's impossible for us to critique it. Obviously there is some reason no one's calling. Like I said, you need a DISPLAY made to put on the counters that you give to them. How...
  21. Replies
    27
    Views
    739

    I don't think that number is accurate. My belief,...

    I don't think that number is accurate. My belief, from extensive testing with some very high dollar equipment, is that when laser manufacturers spec something in CFM, they mean INSIDE their cabinet,...
  22. Then something is wrong. Your prices are too high...

    Then something is wrong. Your prices are too high or your quality is not what people are looking for. If you're in the dog business and you can't sell one pet tag, you've got something else going on....
  23. He's missing the obvious link. Pet related...

    He's missing the obvious link. Pet related products. He's a dog trainer. Sell dog tags to people that sell dogs and cats. Work out arrangements with vets. Create displays with examples and options...
  24. Replies
    14
    Views
    495

    Thanks Mike, that's exactly what I wanted to do,...

    Thanks Mike, that's exactly what I wanted to do, but not what they wanted :(
  25. Replies
    10
    Views
    465

    Not that I'm defending anyone, but they are just...

    Not that I'm defending anyone, but they are just coming off a massive trade show. I have calls into 3 manufacturers for quotes for a piece of equipment from the show and I've yet to get a call back...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4