Try tightening the arbor nut to increase the preload on the arbor bearings. I believe it's # 40 on the parts diagram.
Type: Posts; User: Mike Linne; Keyword(s):
Try tightening the arbor nut to increase the preload on the arbor bearings. I believe it's # 40 on the parts diagram.
Claimed accuracies:
Starretts: 0.0002" per foot
Snap-on: 0.0002" per foot
GW "economy": 0.0060" per foot
So in theory the Starrett and Snap-on offerings are 30 times more accurate. To put it...
Tom,
I have the G513 and had no problems wrestling the saw into my garage from the back of my van.
Some comments:
1. The saw can be placed on its' "spine" on a furniture dolly to get through the...
Symptons described indicate dull knives.
Atlantic Plywood in NJ will sell small quantities and carries cabinet grade plywood as well as baltic birch. Decent prices and they can deliver. They have locations closer to you.
The Easy Bagger is along the same lines as Brian's suggestion. Available at local hardware or borg. Works great.
I've used the following folks to consolidate export shipments from the US (port of Newark):
OPT Overseas Project Transport Inc., 46, SELLERS STREET, KEARNY, NEW JERSEY 07032. TEL : (201) 998-7771...
Atlantic Plywood in NJ will sell small quantities. They typically stock furniture grade as well as Russian birch. Decent pricing and nice to deal with. They recently relocated from Rutherford to...
Per Onieda rep the differences are:
1. Filter is 80%/20% cellulose/polyester versus spun bound filter.
1A. Filter area is larger
2. Asian sourced motor versus Leeson
3. Yellow color versus white...
No - works on twist drills only
Remove the green part that the original blade guard bolts to. The Beisemeyer splitter bolts directly to the trunnion.
Router table planer, drill press and bandsaw all require infeed and outfeed clearance (space to the sides). Lathe doesn't require side clearance. Consider swapping router table with shop vac or...
I attached two pictures provided by Don Ewing of Biesemeyer. One picture shows the inside cabinet attachement of the splitter, the other picture shows the nut/bolt through the hole which was used by...
I have the G7944 (same drill press/floor mount) with an auxillary table and Delta mortiser. Yes the mortiser fits and works, but in retrospect the set-up/removal time are excessive. As mentioned...
In a nutshell the cyclone is strictly a particle separation device. From a woodworker's perspective the advantages of the cyclone over a single stage separator (G1029 type) are:
1. Performance...
I have the Grizzly G0513 and have been satisfied with its performance. However the Wilke/Bridgewood clone was not available at the time. You are correct that the manufacturer is the same for all...
The pin is non-optional and must be used for safety's sake. The pin keeps the insert from rising at the back due to the "blade entrained" air rush, also keeps the back from rising if you push down...
I bought the 3/4" model (750 I think) motivated mainly by job delays that occur when you dull a bit in the middle of a job. You know the scenerio - drilling car frame, bit goes dull, you struggle...
To clarify:
With cyclone air discharging to fan inlet (pull thru): A bottom outlet open to atmosphere will pull air into the cyclone displacing air that normally would be drawn through the "normal"...
For $50 more the G0513 (17") is a better value. 2HP motor, 12" resaw height, more rigid post, sits directly on floor, footprint about the same as the flared stand of the G0570. Functionally doesn't...
The Delta part number is 1349941. I ordered direct from Delta, but there appear to be other sources also (www.sawcenter.com for one). The splitter is/was originally part of the Unigard blade guard...
Don can help with part numbers and installation questions for Biesemeyer products. For the right tilt 1023 the Bies drop in splitter (has the pull knob) works and also the Delta splitter with the...
Atlantic Plywood Corp
(215) 538-3774
195 Kelly Rd
Quakertown, PA 18951
Russell Plywood in Reading
I have the 1023 with a WWII blade - no vibration, passes the dime test and no scoring. Runout on the arbor is < .002". One thing to try is to remove the belts and check vibration. If you still...
Woodworkers Supply is selling this model for $99, so with rebate net cost is $69.00 - good deal for a nice grinder. The tool-less feature works great.