Search:

Type: Posts; User: Bob Michaels; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    2,071

    I just bought one of the steel containers made...

    I just bought one of the steel containers made especially for such purpose. I think it was about $60 on Amazon. I increased the safety by putting a galvanized old bucket inside of it with water in...
  2. Replies
    7
    Views
    2,762

    Rick, you may want to try a sheet of pegboard,...

    Rick, you may want to try a sheet of pegboard, cut to the size of your bench, as an accurate way to layout the hole positions. Just put a circle around the pegboard holes you want to use and ignore...
  3. Joe, see Dennis Tebo's post with photos further...

    Joe, see Dennis Tebo's post with photos further down, that's the saw. You can get an idea of the small scale by comparing it to the left and right miter slots of the full size table saw.
  4. Yup, that's the one that I have too. It truly is...

    Yup, that's the one that I have too. It truly is a masterpiece. Bob Michaels.
  5. Joe, I will try to post photos tomorrow.

    Joe, I will try to post photos tomorrow.
  6. If you don't mind spending some bucks Proxxon and...

    If you don't mind spending some bucks Proxxon and others make mini table saws for people who do model railroad buildings. About 7 years ago, when I was interested in a mini table saw for small work...
  7. Replies
    3
    Views
    1,876

    Thanks Mel.

    Thanks Mel.
  8. Replies
    3
    Views
    1,876

    Gluing cedar

    I'm making a 4' x 5' exterior sign board for mounting a few commercial tenants individual sign boards on. The sign board is a sheet of 3/4" MDO epoxied (West system) to a 1/2" sheet of MDO. That's...
  9. Replies
    12
    Views
    2,126

    That is a beaut. 30" wow!!!

    That is a beaut. 30" wow!!!
  10. Thanks, Ed.

    Thanks, Ed.
  11. DeWalt cordless multi-tool vs Fein cordless

    I have been using Fein MultiMaster for years and it's an amazing tool. I have a project repairing a free-standing directory sign that is not near power so I purchased a bare DeWalt 20 volt Max multi...
  12. Replies
    9
    Views
    1,943

    I would also be interested to hear what blades...

    I would also be interested to hear what blades other people use and where they buy them. I have been using the corded Fein MultiMaster for years with expensive Fein blades. Just bought the Fein 18...
  13. Replies
    6
    Views
    1,354

    Julian, I have pretty much the same L shaped...

    Julian, I have pretty much the same L shaped setup with wood edging & open squares to slide the clamps in. Mine has been in a 4' x 8' white laminate outfeed table for several years. Very handy. ...
  14. Replies
    12
    Views
    8,791

    Same as Paul Girouard.

    Same as Paul Girouard.
  15. Fred, my wife always cleans and saves used...

    Fred, my wife always cleans and saves used cottage cheese containers as well as deli containers & other round or square food containers for my use to mix 2 part epoxy. I really love West System...
  16. Thread: Air Shim

    by Bob Michaels
    Replies
    1
    Views
    829

    Air Shim

    Has anyone tried the Air Shim or Air Shim Pro and what are your comments? I would appreciate your opinions.
  17. Doug, the good news is that cast iron is soft and...

    Doug, the good news is that cast iron is soft and easy to drill and tap new threads, if necessary. I realize this is a big purchase but once you get past this you'll really enjoy the drill press. ...
  18. Jay, just a wild thought but you might consider...

    Jay, just a wild thought but you might consider hinging the house at the midpoint of the side wall so it opens like a book. Since your home is traditional in style it probably has a center bearing...
  19. Replies
    29
    Views
    5,513

    Randy, the nozzles are not reusable from session...

    Randy, the nozzles are not reusable from session to session for the reason that you stated. I remove and discard the used nozzle at the end of a session and replace the small divided plug into the...
  20. I would follow Jim Becker's response of simply...

    I would follow Jim Becker's response of simply staggering the joints. My preference would be to use longer members and arrange the joints in a random, but sensible, pattern. Use several culls...
  21. Replies
    15
    Views
    3,012

    I used 4 ball bearing hinges per door when I...

    I used 4 ball bearing hinges per door when I built frame & panel garage doors out of 2 x material with 1/2"ply panels. These doors were not 200 lbs each but pretty heavy. The 4 hinges were used to...
  22. Replies
    39
    Views
    6,268

    I agree. They work pretty well for me. I have 2...

    I agree. They work pretty well for me. I have 2 of them on the lathe and one each on band saw, chop saw, router table, drill press, grinder, sharpening station, belt/disk sander and oscillating...
  23. Replies
    2
    Views
    1,258

    Thanks, Jason. I think you're right on the...

    Thanks, Jason. I think you're right on the money. Since it was less than 24 hrs since I applied the poly, even 120 loaded up. I sanded with 80 and that was loading but I finished up taking it back...
  24. Replies
    2
    Views
    1,258

    Can I apply paint over poly

    I just stripped an old pine door and brushed clear oil based Minwax quick drying poly over the raw pine. Now, I really don't like the result and was wondering if i can just scuff up the oil based...
  25. I may be misinterpreting your drawing, but, are...

    I may be misinterpreting your drawing, but, are the small rectangles under the sheets of plywood supposed to be floor joist locations? If so, the decking is not running perpendicular to the joist. ...
Results 1 to 25 of 283
Page 1 of 12 1 2 3 4