Search:

I received the pulley set from Grizzly today. I worked a good while getting the inner pulley half to slide on the shaft by hand. Then when I pressed the bearing on it got tight again, more fitting...

I got it apart. What I didn't understand was that the bearing was pressed on to the pulley. With most of the pulley broke away I used the puller hooked on the control bracket (right in picture) to...

What I thought was some Gentle tapping with a block of wood and a hammer broke a piece of the pulley off. Luckily the pulley set is listed as still available for $18. I don't have it off yet,...

I haven't had my lathe on in a while until yesterday. I needed to repair the pole for my son's patio umbrella. I could never get the reeves drive lever to move off the slowest speed. I managed to get...

I cut down a 12 inch maple this week. I saved six 3-4 ft pieces from the burn pile. Any forum member is welcome to some or all of it. On I-59 in NW GA. PM for directions. 271354271355

Links to other forums are sometimes frowned upon here. If you google "Wood Forum, Tools and Tool Buying" you should be able to find it. I would call Grizzly and ask them, maybe they can tell you,...

I have read that the early Grizzly G1022 contractor saw was a clone of the 63. Some parts might be available from them. What do you need? There is a discussion about that saw on the Wood Forum, Tools...

I always set the fence off the miter slot, close as I can get it without being closer on the rear. I believe the miter slot should be the bench mark for setting the fence and the blade.
Cannon

I have an older Delta 22-540 lunchbox planer that I have never been able to adjust the snipe out of. The few times I have cut to rough length and planed sanding out the snipe has been a pain. I much...

I was able to fool with it a while this afternoon. I went over it with a toothbrush size wire brush as Shawn suggested the washed it down with mineral spirits. Taping off the machined surfaces on the...

I bought this plane a the flea market a couple of years ago and have never done anything to it. Yesterday I was trying to get my cheapo sand blaster to work and used the plane to try it out. The...

I would go ahead and buy a dial indicator and magnetic base, there handy for a lot of tool setup jobs. Remove the wheel and setup the indicator on the shaft near the outside end of the bearing...

I don't think that is necessarily true. This is a link to a post of a member with a Biesemeyer for sale.
http://www.sawmillcreek.org/showthread.php?p=1380620#post1380620
Cannon

There is a discussion on the 'Wood FORUM' in tool and tool buying, But it relates to the arm being broken and the bracket intact.
Cannon

Ray, did you ever see one with this type of built in caster system. It's a little odd but I think it could be handy with better casters.
Cannon

This is my third bandsaw, a fact my wife pointed out to me. I have a Craftsman/Emerson 12 and a old model Grizzly 18. This one will replace the Craftsman. I had ordered Mike D's original bandsaw book...

Thanks Mark
This machine has a Pittsburgh serial number tag. The number begins 84M, M does not seem to be shown as a valid month code. Anyway sometime around 84 is close enough.
Cannon

I bought this 14 inch Rockwell bandsaw (28-243) off Craigslist yesterday. I got it home and found a few things that seem not to be right. The tire is loose on the bottom wheel, can this be fixed with...

Shouldn't the Highest point of the head also be the highest arc of the knives?
Cannon

PM's returned.
Cannon

I have some pieces of walmut from a tree I cut in NW GA south of Chattanooga. It may not be worth anything but if anyone wants it their welcome to it. PM if interested.
Cannon

Yes you should buy it. I have had an 1182Z with levers for several years and never had any problems with it.
Cannon

I don't know what size (thickness and width) but I saw these on amazon yesterday.
...

I wonder if the jibs might bend in the area not backed by a knife.
Cannon

Thanks
Apparently they are not worth much if anything. I'm going to take the hardware off them and throw them on the next brush pile.
Cannon