Search:

Type: Posts; User: Kyle Fries; Keyword(s):

Search: Search took 0.23 seconds.

  1. Replies
    2
    Views
    3,489

    I think it fixed it. Thanks

    I think it fixed it. Thanks
  2. Replies
    2
    Views
    3,489

    Pictures Do Not Load

    Not sure if this is a new or old problem but pictures in post do not load on my computer. When I click on the link I get an error that states I do not have permissions to edit the post.
  3. Replies
    11
    Views
    1,541

    Be careful not to over grease. We have had...

    Be careful not to over grease. We have had several motor failures at work due to over greasing. Definitely need a drain hole for the old grease to come out of like Lee has on his saw.
  4. Replies
    7
    Views
    2,692

    I have purchased some parts recently from Bob...

    I have purchased some parts recently from Bob Kaune and I have purchased from NH Plane Parts through eBay. Both have excellent service and should do you well. I reached out to Bob through e-mail and...
  5. Replies
    5
    Views
    1,376

    Thanks for all the help. I will double check the...

    Thanks for all the help. I will double check the screw size and pitch. I have looked at that before but I can't remember what it worked out to be. For now it is a Frakenshave!
  6. Replies
    5
    Views
    1,376

    Help to Identify a Spokeshave

    I Bought this spoke shave at a flea market. The blade is a Stanley blade but the body has no markings at all. I cleaned it up when I got it but I do not think it was every painted and I have left it...
  7. Replies
    61
    Views
    10,278

    I have a Baileigh MC-1000. I took it off of the...

    I have a Baileigh MC-1000. I took it off of the base and mounted it to my bench. I have being using it more and more recently. The one change I have made is to remove the stop rods and replace them...
  8. Replies
    7
    Views
    2,732

    Both shafts measured the same and were within a...

    Both shafts measured the same and were within a couple of thousandths. I am using high quality machinists calipers and depth gauges to measure everything. I had not thought of spring washers as...
  9. Replies
    7
    Views
    2,732

    I looked through the parts manual several times...

    I looked through the parts manual several times and it never showed a spring washer in that location. There wasn't one in there when I took it apart either. I do not think it had been taken apart...
  10. Replies
    7
    Views
    2,732

    Jet JWBS-14 Bandsaw Rebuild

    I recently tore down and rebuilt a Jet JWBS 14 band saw. I had the band saw in may garage for a while and did some minor work to it but recently decided to do a complete overhaul since I needed to...
  11. Replies
    27
    Views
    3,096

    Victor Machine Exchange Inc. has a lot of the odd...

    Victor Machine Exchange Inc. has a lot of the odd ball sizes. Not sure if they have a 9/32 LH. They do have some of the taps and dies for the other odd staney threads.
  12. Replies
    10
    Views
    5,077

    Thanks for the tips. I will have to check the...

    Thanks for the tips. I will have to check the knives, clean the rollers and try waxing the table.
  13. Replies
    10
    Views
    5,077

    DeWalt 734 Planner Feed Rollers Slipping

    Does anyone have any advice for keeping the feed rollers clean on the dewalt 734? I have tried wiping them down with acetone and have had little luck with the cleaning lasting. I did spray down the...
  14. Have you tried to turn the sprocket around so...

    Have you tried to turn the sprocket around so that the teeth are on the inside? Cal the aluminum spacer be turned 90 degrees or shortened?
  15. Replies
    6
    Views
    9,271

    Thanks for the thoughts guys. The dilemma I have...

    Thanks for the thoughts guys. The dilemma I have is that it is a $400 planer new and the head is another $400. I am a DIYer as well and work in my basement. I floor model would be a bit tricky to get...
  16. Replies
    6
    Views
    9,271

    DW734 Shelix Head Upgrade

    Is it worth upgrading to a shelix head on my Dewalt 734 planer?
  17. Thread: Tie Rack

    by Kyle Fries
    Replies
    6
    Views
    5,948

    Tie Rack

    My day job requires that I wear a tie. The tie rack my wife bought has run out of space for the collection of ties that keeps growing. Any advise on a rack design or what to use for hooks so that I...
  18. Replies
    7
    Views
    1,709

    John, Does the insert go through the bearings?...

    John,
    Does the insert go through the bearings? If so you may want to replace the bearings when you have it all apart. I have rebuild and replace bearings on a lot of older press presses and lathes....
  19. Replies
    0
    Views
    609

    Foley Rachet Bars

    Has anyone had a rachet bar machined for a foley toother? I have been searching the forum and could not find anything recent on the subject.
  20. Replies
    1
    Views
    1,035

    VFD upgrade - Awesome

    I have an old Brodhead Garret that had a variable speed reeves drive. I was having trouble with it burning up my belt. Reading through the forums I discovered guys install VFD drives. Best decision...
  21. Replies
    3
    Views
    1,163

    The lathe has a Reeves Drive. Does anyone know...

    The lathe has a Reeves Drive. Does anyone know how to set the belt tension on a Reeves Drive?
  22. Replies
    3
    Views
    1,163

    Mark, I have the crank but I do not have the...

    Mark,
    I have the crank but I do not have the step pulleys as shown. The crank on my unit is for variable speed adjustment. I'll get a picture tonight and post it tomorrow. There are these floating...
  23. Replies
    3
    Views
    1,163

    Brodhead Garret Lathe Belt Tension

    I have a brodhead garrett J-line 112 with the variable speed pulley set up. Does anyone know how to properly adjust the belt tension on one of these? My belt always ends up being too tight or too...
Results 1 to 23 of 23