Search:

Type: Posts; User: Steven J Corpstein; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    1,549

    Need some opinions

    I've come to a point where I am going to sell my larger shop tools and wondered if I'd be better trying to sell them separately or as a full shop? Problem is once I sell one of them, I'm out of luck...
  2. I also purchased one of David's guides. Before...

    I also purchased one of David's guides. Before getting it, my dovetails looked like a hack had done them. After watching David's techniques and using his guide, they are pretty respectable now. I...
  3. Replies
    11
    Views
    2,607

    I've also got that set of stones and find that...

    I've also got that set of stones and find that using 80 grit sandpaper is way faster and controlled when stuck down to some float glass or a cheap granite plate. You can purchase rolls of PSA 80...
  4. Replies
    36
    Views
    9,503

    I purchased the Lie Nielsen and after using it...

    I purchased the Lie Nielsen and after using it for several projects, bought the Lee Valley router. I like LN tools, but this one should have spent a bit more time in development. The small blade...
  5. I have never had very accurate results with the...

    I have never had very accurate results with the Wixey stuff, so I switched to a Tilt Box. Same thing with Wixey table saw DRO, I switched to a Proscale by Accurate Technology. Wixey's seem to be...
  6. Replies
    8
    Views
    1,338

    I covered mine with some Formica, it's been great...

    I covered mine with some Formica, it's been great to work on and doubles as an assembly table that glue comes off of easily.

    277574
  7. Replies
    4
    Views
    2,018

    And that is why they're at the top of their game....

    And that is why they're at the top of their game. Cudos guys, nice film that says a lot about Lee Valley.
  8. Very nice, looks like you still got the gift.

    Very nice, looks like you still got the gift.
  9. Replies
    5
    Views
    1,653

    Very, very nice!

    Very, very nice!
  10. Replies
    8
    Views
    2,372

    Dewalt 621

    Dewalt 621
  11. I went through a long series of how the heck to...

    I went through a long series of how the heck to sharpen, all the time wanting to learn to hand sharpen and get rid of the gadgets. I bugged Derek, bugged Harrelson and just about anybody else that...
  12. Or you could invest and go this route. With this...

    Or you could invest and go this route. With this setup, you eliminate having to use a spacer and can dial in the dado position within .001".252938
  13. What stones??????

    I purchased mine from Stu at Tools From Japan. Stu knows his stuff and the shipping was much quicker than the 3 -4 weeks stated. I purchased the Sigma ceramics and really get a sharp, durable edge....
  14. If you were referring to when I got mine, I've...

    If you were referring to when I got mine, I've had it for about 4 years, right before LN started offering the higher frog option.
  15. After reading all of the posts, I decided to...

    After reading all of the posts, I decided to chime in. I just went out and looked at my LN 4 1/2 to see what I had for clearance on the CB hole. MY CB is/always set to within .010 or less of the...
  16. Replies
    5
    Views
    2,214

    Sharp Skate Honing Guide

    Has anybody tried one of these honing guides? I just sent one back to Woodcraft because the axles were not drilled and tapped on the same center-line causing the middle wheel to be high and that...
  17. Replies
    8
    Views
    3,178

    Absolutely amazing.

    Absolutely amazing.
  18. Replies
    36
    Views
    8,682

    Here is how I did my outfeed. Big enough for how...

    Here is how I did my outfeed. Big enough for how I work and portable.

    http://www.datasystemsltd.com/extension
  19. Replies
    7
    Views
    1,800

    TS-Aligner Owners

    I replaced the original one with a Starrett 25-441 and it works fine. I got mine here and got the one with the 1.000" range.

    http://www.mytoolstore.com/starrett/dial01a.html
  20. Replies
    13
    Views
    2,475

    I purchased a General 650 saw 5 years ago and if...

    I purchased a General 650 saw 5 years ago and if I were to be looking for a new saw, I'd buy a General 650R (new model w/riving knife). I think they make a very solid well built saw, their cast iron...
  21. Replies
    1
    Views
    1,259

    I own that jointer and really like it. Mine was...

    I own that jointer and really like it. Mine was purchased new, maybe 3 years ago, and I've had nothing but good results from it.
  22. I'm with Roger, I hit them with a hand plane or...

    I'm with Roger, I hit them with a hand plane or at the very least a card scraper. I tend to try and not use sandpaper if I'm going to use any finishes with color, as I think the grain looks muddy...
  23. Plus 1 on the Proscale. I did a huge amount of...

    Plus 1 on the Proscale. I did a huge amount of research also and couldn't be happier with the Proscale.
  24. Here are some pictures of how I tackled both...

    Here are some pictures of how I tackled both portable and big enough on my saw.

    http://www.datasystemsltd.com/extension
  25. I struggled with this very same question and...

    I struggled with this very same question and finally came up with what worked best for my usage. I've included a link to a pictorial web site that I had thrown together for someone that had the same...
Results 1 to 25 of 260
Page 1 of 11 1 2 3 4