Search:

Answers to all of the above.
#1) Life is an expense within itself.
#2) I am going to invest the time, yes, and money into becoming a certified marine tech just so I can officially repair my own...

YEP, I sold some of my WW equipment to get a new toy.
http://www.nokomismarine.com/cgi-bin/SearchEngine/jsp/photo_gallery.asp?boatid=1081273&vehicleType=N&picpos=0

And I LOVE IT.:D:D:D:D:D

Sounds as though not all the drivers were installed for your hardware,
(i.e., monitor, keyboard, mouse, etc.)
You need the original program driver disk(s) for the system & reinstall completely....

The infeed roller is semented. To answer the last ?
I have called PM repeatedly & ater much discussion we are coming to the conclusion that my planer may very well have a bad bearing holding the...

Ya know,
If ya bought a Billy Goat you wouldn't have these problems.
Just stick him in the barn until the (yard & the trees & anything else he can get a hold of) needs trimmed.:)

To answer all of the above questions.
Yes the bottom of the boards shown are flat & smooth, or at least they were until I ran them through the PM 209. Chattered now.
I started originally planing...

Pic's of problem
Hope they help

Brian,
I haven't turned the cutter bits as of yet but did inspect them & they feel pretty sharp to me.
As stated before I have only ran 200BF through the unit since it was uncrated.
Would...

No we didn't catch anything, just a sun burn. Too hot I guess.
And yes I did try short stock compared to long stock after I recalibrated EVERYTHING.

Just spent 4 hr.'s going through the entire machine w/ a dial indicator making sure everything was set properly, not to mention everything was cleaned & lubed. (whether it needed it or not)
My...

The scalloping is from the beginning of the board to the end.
Yes, we have changed gears for slower feed rate.
It has my tech & PM scratching our heads & nobody seems to know why its doing this....

Will try your suggestions Brian.
Will also take pics later & post results.
For now, going fishing. :D
In reference to the cutters being dull, I've only ran 200BF through the machine since it was...

Hey Brian,
The tech & I both double checked the cutters & the rollers are set @ .005., what PM recommends.
I'm clueless.

My PM 209HH is producing a rippled effect on my lumber.
The unit is 1 yr old & has only been used on 200BF of lumber to date.
I had the local machinery tech come out the first time it was used & he...

Peter,
Try these guys, they can make you anything you want.
http://cggschmidt.com/

Alan,
There are companies which sell T&G or V edge banding router bit sets.

Your absolutely correct about HVLP spray guns, but, regular siphon feed spray guns suck up alot of continuous air & I didn't think he wanted to spend $350 plus on a professional HVLP gun.
If he...

I am going to build an entertainment center for the family.
With that said, I would like to use maple but am leaning towards Hickory to same myself some money.
My supplier emailed me stating...

It's expensive to start.
When I got mine I had to fine tune it to true cutting degrees.
It was off by .75 degrees, no big deal.
I then realized it takes alittle getting use to mastering a clean...

Brian,
Jim is giving you good advice.
I too purchased me IR compressor from Tractor Supply at a very attractable price, like $300 cheaper than anywhere else I could find.
1st of all if...

Rich,
Thanks for adding the cola thing. Coke is actually the best to add as it has a high acidity content and helps tenderize the meat.
Also one may want to add some liquid smoke, just be...

Here's a awesome BBQ rib receipe.
EVERY AMERICAN LOVES RIBS.

Cut your ribs.
Season w/ everglades seasoning. A southern thing. http://evergladesseasoning.com/
Pour (1) full body beer into rib...

Like I said before, Bob Hughes of OleGeneralStore is the only mill owner I have personally dealt with so I can't say what to expect from these other supplies.
I realize not everybody is within...

If your looking for a honest wood supplier who owns a saw mill then this guy is it.
His name is Bob Hughes located in Geneva, Fl. (Orlando area.)
His price listing is very reasonable & can be found...

Rob,
#1, Nothing was edited.
#2, WHO ARE YOU TO ACCUSE SOMEONE OF EDITING SOMETHING WHEN YOU DON'T KNOW IT WAS EDITED FROM THE START.
The add stated word for word what was posted.
I emailed the...