Search:

Type: Posts; User: Richard Venturelli; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    1,711

    Not sure what your problem is. If the glue is not...

    Not sure what your problem is. If the glue is not holding and you did write about exotic woods. Some Exotic's have lots of oils in them you may need to get some special epoxy for oily wood. I think...
  2. Older Green JET 18" Bandsaw Questions on Bearing Guides?

    Hello all, Been a long time member but its been a while since I've been here. I bought an 18" Green Jet Bandsaw for 200 bucks and finally was able to start working on it today when I received. a...
  3. Replies
    23
    Views
    3,332

    I'd run 3 wire 12 and use two 20 amp circuits hop...

    I'd run 3 wire 12 and use two 20 amp circuits hop scotching each box. If using red and black as power source then hook in Red to the first box then black to the second box then red to the next, down...
  4. Replies
    4
    Views
    3,000

    That would be perfect if in the Rancho Cucamonga...

    That would be perfect if in the Rancho Cucamonga or Alta Loma area.
  5. Replies
    4
    Views
    3,000

    Woodworkers Shop Rental

    I'm wondering if anyone in the Southern California area has or knows of a shop you can rent on a daily or montly basis? I have heard of these but wondering if any exist in my area? I also wondered...
  6. Replies
    13
    Views
    1,929

    Bought a Jet JWCS-10A-PF Cabinet Saw off Ebay...

    Bought a Jet JWCS-10A-PF Cabinet Saw off Ebay Locally for $400.00 It was barely used. Guy said he used it to cut paneling. Cast Iron Top and Extension table and he threw in some extras. Think I got...
  7. Good Article and Reference

    Good Article and Reference
  8. Replies
    8
    Views
    1,397

    ShopNotes & WoodSmith, I like rags with no...

    ShopNotes & WoodSmith, I like rags with no advertising..
  9. Im particial to my Porter Cable 14.4 with the...

    Im particial to my Porter Cable 14.4 with the hammer drill options that I've had for 7 years and its still running strong. I have replace some batteries but I use this drill everyday!!! I have a...
  10. Replies
    23
    Views
    2,694

    Pine, Poplar come to mind. Depending in what part...

    Pine, Poplar come to mind. Depending in what part of the country you live. Red Oak is reasonable. Just jump in and don't get frustrated.
  11. yeah and in California they like these heavy...

    yeah and in California they like these heavy looking shelfs, meaning you have a top and bottom about 2" to 3" thick and a piece of trim or decorative chair rail over the front edges. 1/4 round would...
  12. Another good solution! And it's fast. Think I'll...

    Another good solution! And it's fast. Think I'll try this using a measuring stick. Still see the need for a scribe if the walls (joint compound build up) are out of wack.
  13. I was thinking about using drywall shims, long...

    I was thinking about using drywall shims, long cardboard pieces about 1-1/2" wide and a glue gun, but if I need it to fit tight I will still have to use a scribe because of drywall never being flat....
  14. It depends on how accurate you can measure. I...

    It depends on how accurate you can measure.
    I usually use a large compass, but 2 shorter pieces of light metal or wood strips that are shorter than the whole distance needed to measure will work. ...
  15. I was using the larger measurements for example...

    I was using the larger measurements for example only. I would never leave that much, the angle would be to steep and would not be a true measurement for where the shelf would set. Like you said 1/4...
  16. Let me see if I got this right, Using 36" as an...

    Let me see if I got this right, Using 36" as an example of the opening, cut the shelf 37" set your scribe at 1/2" place shelf in opening on angle and scribe. Place the other end on angle and scribe...
  17. Replies
    17
    Views
    3,474

    Never had this problem with the Kreg and use it...

    Never had this problem with the Kreg and use it all the time. Like others have already stated, make sure youre starting out with squared ends and clamping the two when driving your screws.
  18. How do you lay out a shelf in an opening that is not square?

    Wondering if anyone has a fast and effective way of measuring and laying out a shelf in an opening that is not square? I have been installing shelf's in niches which have become common in new homes...
  19. That's what that little voice is saying, think...

    That's what that little voice is saying, think I'll listen to it this time!!!!
  20. You guys are right, I'll make money just not what...

    You guys are right, I'll make money just not what I would usually make. I really have no overhead, it would just be time and that hourly rate would be much less than normal. I only know one way of...
  21. I'm thinking the same thing about this customer....

    I'm thinking the same thing about this customer. I always try if I can, but if it's not worth it then why. Matter of fact it would be a red oak stain or look, I'm in California and Red Oak is not as...
  22. How do you make a cheap species of wood look good?

    Have a customer that wants to go cheap on a TV cabinet to fill a family room niche. I have built many painted and hardwood TV cabinets but the money he wants to spend I'm not sure I can build him a...
  23. Don't you hate it when the heat register gets in...

    Don't you hate it when the heat register gets in the way of crown molding??? I have moved the registers in some instances but that's not always practical.
  24. Replies
    4
    Views
    975

    Here's one I built a few years back for a...

    Here's one I built a few years back for a customer. It was not a kit and it's all made of poplar. It incorporates a bookcase to. I also did the tile on the fireplace face.


    ...
  25. Good for you, I'm glad you jumped into it. You...

    Good for you, I'm glad you jumped into it. You get a certain satisfaction when doing it yourself. Keep up the good work. And I'm sure youre not the brunt of this post.

    I've built many things, when...
Results 1 to 25 of 75
Page 1 of 3 1 2 3